I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
Currently the Peripheral Preferred Connection Parameters UUID 2A04 is by default enabled in the BLE examples. According the BLE spec its not a mandatory parameter the peripheral...
Related to devzone.nordicsemi.com/.../ , how should the last parameter to sd_ble_gattc_primary_services_discover() be cooked for 128-bit service UUIDs?
printf("Discovering...
Hi Man,
How many CENTRAL_LINK_COUNT in ble_app_hrs_rscs_relay can do so far?
I just increase the CENTRAL_LINK_COUNT form 2 to 5 then nRF52 Reset itself all the time.
...
Hi,
I'm trying to run my application on your PCA10031 and PCA10000 USB Dongles and I'm having a problem getting the UART receive to work on the PCA10000-- my application...
Hi,
I want to to use an external ADC for the NRF51 since the resolution for the NRF51 goes up to 10 bits and I want to use a system that goes up to 16 bits that has a sampling...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Are there documents other than "S110 nRF51822 SoftDevice Specification v1.2" that describe the SoftDevice resource usage? I am particularly interested in the S130 on the nRF52822...
Hi,
I`m a newbie user of nrf52, i want to know what are the neccesary libs to configure the BLE on nrf52 and what are the steps from the scratch.
Thanks
Hi,
I am using nRF52832 with S132_V2.0.1 and SDK_11.0.0. I have set advertisement interval at 2 second.
I have observe one thing in advertisement that many times device...
Hi!I work with a Beacon Kit (nrf51822) and I would like to know which is its default radio transmit power and the velocity of transmission. In my application I sent via Ble...
Hi,
I'm using the reference project "Experimental: Eddystone Beacon Application" to transmit Eddystone URL packets and I'm sniffing the data with Wireshark.
I noticed...
Hi,
I'm using nrf51822 board with SDK 10 and S110 softdevice.
My application is based on uart over ble. It take 20 bytes data from a android device using nus, store that...
I have created files before with s110 sd8 with the
nrfutil.exe utility using a bat file.
nrfutil.exe dfu genpkg --application nrf51422_xxac_s110.hex --application-version...
Hello,
I want to connect one board trough SPI to my nRF51-DK. Using SDK11 and SD130, the nRF51-DK is the SPI master, I call the function nrf_drv_spi_transfer() but the...
