Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
Internal fault[0xb3b91b:5060750] occured during linking when disable the log output by [#define NRF_LOG_ENABLED 1],
but no error occured when eanble the log output by [#define...
I know there are other (long!) threads about PDM mics and I've studied them all carefully. Unfortunately I'm still having an issue with our on-board mic. The difference is...
Hi,
Toolchain manager is failing to download SDKs.
I am using:
Windows 10 PC
3.7.0v nRF Connect Desktop application
0.9.3v Toolchain manager.
Downloading sometimes...
Where is the provisioning configuration data getting stored ?
1. EEPROM
2. Any other non volatile memory
Is it getting stored in external chip to nrf52833 or inside...
Hello there!
I'm quite new to the topic and just tried to dig into it a bit, so I'm sorry if I didn't get all things yet about the nRF5280 Dongle :) .
Right now, I'm following...
Hi all,
Using the thread CLI example (on a PCA10056 board) as a starting point I would like nodes to connect automatically to a thread mesh when booting. I then want to...
I use the following example source code to test NFC pairing.
Example source code for NFC: nRF5_SDK_17.0.2_d674dde\nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\experimental...
Hi
thank you very much for your paying attention.
Yes the peripherial_uart sample seems to be a good choice for my project. But Uart 0 pins didn't come out on GPIO connector...
Hi,
We are trying to create a network using 20 movesense sensors and BWG840 Fanstel gateway acting as the central. The gateway is running a modified ble app uart multilink...
I'm a beginner in BLE applications, and I'm having trouble with connecting nRF toolbox application
I wanted to use UART function provided in nRF toolbox.
But, an e rror...
Hi,
I wish to run an existing project in Segger embedded studio for its debug capabilities (Currently the project runs in VS code).
I'm using the nrf52832, running a bare...
I'm trying to add the unity test integration to our project, but failing to build, since the project has a dependency on nrf_oberon
For the sake of completeness, the project...
I'm having trouble connecting Thingy:91 to cloud.
I've installed both the modem and HEX image in the board successfully.
I've added the SIM card successfully to the...
I've had intermittent issues with the nrf9160 modem using mfw 1.3.0 with an iBASIS SIM getting stuck in "searching" state when first powering on. The symptoms are similar...
I am using a nrf_drv_twi_tx() and nrf_drv_twi_rx() for a simple I2C transaction but I'm noticing a strange behavior.
If I don't use APP_ERROR_CHECK(err_code); right after...
