Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hello,
I hope you are well.
I am currently working on interfacing an INTAN RHD2164 chip with the NRF52840. This chip is connected in SPI with the NRF52840. The only problem...
I tested NB-IoT and MQTT in NRF9160, and the device could normally search for NB signals and connect to our background through MQTT protocol. After the device uploaded data...
NRF52840, S140, SDK 14.2
I am trying to write to an SD Card. But whenever I insert the card, I get a failure on ASSERT. I believe this is because I am using P0.0 as the...
Hi Nordic,
I understand that there's a way to monitor the RSSI of a Bluetooth connection using appropriate API from softdevice library. But we are currently developping...
Hi,
I'm currently working on a ble mesh project with 2 nodes using nrf Connect SDK v1.4.2 with toolchain 1.4.2:
Device A with Time Client Model - nrf52840
Device B...
Hi.
I would like to flash an external sensor with the Jlink and then to "talk" with him through the internal sensor.
Can I know which sensor an I flashing? All the time...
I handle events directly by invoking the following code after the sd_app_evt_wait(); call:
I poll the events and dispatch them to my handler as needed.
Now if I do this...
What is the operating temperature range for the Nordic Thingy 52? I cannot find it anywhere in the documentation, but there is documentation on all its other sensors.
hi,
After the TX interrupt event occurs, on_radio_disabled_tx() is executed.
There is a timeout event for receiving an ACK. I noticed that the timer timeout was set...
Hi
I'm a bit unsure as to how to interpret the documentation. It's my understanding that zephyr v2.4.99 is an unstable development release. But it seems to be the only release...
Hello,
4-byte long SPI messages, "1234", are sent to nRF 52DK. The code in DK is attached below. The XFER_DONE event is created before the message ends, which happens very...
I thought this would be rather simple as I would design a BLE peripheral in the usual way but the source of data for the peripheral comes from a sensor sending nonconnectable...
Hi,
I am exporting SAADC example to NRF52840 Dongle and I can see this structure:
/** * @brief Input selection for the analog-to-digital converter. */ typedef enum { NRF_SAADC_INPUT_DISABLED...
Hi,
I get read service content retained after reset, and it is read by the central before I get the chance to change it. Please advise how to clear it upon restart.
Thanks...
I want to create two switch EP(if it is possible I would like to it as much switches as possible).
I am using WIndows 10 with Segger and nRF COnnect SDK v1.5.0.
I tried...
