When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
hi,
I am currently learning to use the mpu6050 read and write code in the SDK from the nrf5_sdk_12.3.0_d7731ad to control mpu9250. The part of the gyroscope and accelerometer...
Hello,
Is it possible to program nRF51822 with nRF52DK (PCA10056) ?
Currently I am trying to program my custom beacon (nRF51822) connected via SWD P20 header. I am using...
Hi
I succeeded to run the DFU OTA process and updated only the application. Application is running OK
The problem is that after repower the application is running but...
Hello,
I am trying to add NFC wake up functionality to the project based on ble_uart_app example;
Using SDK14.2 SD132 V5,1 using DK52 development board
I have added...
Hi,
I am trying to add interruption on light switch example. So, eu studied the gpiote example from SDK14.
When I add PPI, GPIOTE and TIMER libraries, on light switch...
So I have my custom board up and running (nrf51822) pluged into the nrf51DK with RTT debug comm and uart comm working, also starting some initial experimentation.
...
Hi,
I am using ble_app_uart service in my application. In my custom board GPIO pin 8 is used for LED. But this particular GPIO is configured for UART RTS pin in ble_app_uart...
When an NUS Central has several NUS Peripherals connected, is it possible to send the same "message" to all of the connected peripherals at once?
Or do I just have to iterate...
Hi,
It looks like we're experiencing an issue with uart's and digital inputs on an "S132 SoftDevice". Both an UART and digital inputs are used. The UART is initialized using...
Dear Sir/Madam,
I am playing with SDK12.2 on PCA10028 board and runs its HRS example. This example has a battery service and its battery level characteristic could update...
I use DFU. All ok. But I need to store my settings after update. As I was advised, I located my data from address 0x72400
But Keil added after this struc some code
...
Please Find the Attachment Screen shot of SDK Document for Advertising Module. Also Side by Side I am doing Code Walkthrough Blinky Peripheral . The Code in Blinky No Where...
Hi,
In function advertising_init(void) , I have set
and in function gap_params_init(void), I have set
still the icon doesn't change. What could be the possible reason...
Hello,
I'm trying to program my custom board with a PCA10056 following this scheme (Note that my custom board is powered by the PCA10056) :
VDD (PCA10056) ---> VTG(PCA10056...
