hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
How do I check what version I have installed?
The 'Getting Started' page states a minimum version of 9 .5. 0:
http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom...
So what steps do we need to take to have these two different Python versions both installed & usable at the same time on the same machine?
The ' Installing the toolchain...
I have three PCA10056 development boards and have loaded the BLE mesh light_switch proxy_server onto all of them (SDK v2.2.0) which incorperates soft device S140 V6.0.0
...
Hi all !
I'm struggling to get a frequency jumping protocol up and running and can't figure out how to handle the following situation (please refer to the attached "pseudo...
Let's have light-switch provisioner, server and client.
My question is, how to send a message from a client or a server to the provisioner? In order to send a message, client...
Hi,
As part of my project, I need to use the SD card drivers of the nRF5 SDK and the I2S driver. The issue I am having is the following:
If I use pin 31 as the SCK signal...
Hi
This is a heads up that in SDK15.2.0 and file nrf_esb.c you have the line
m_rx_fifo.p_payload[m_rx_fifo.entry_point]->rssi = NRF_RADIO->RSSISAMPLE;
it should actually...
Hi
My application uses NFC for various reasons, and I need, at runtime to load up to 4 textural NDEF records onto the Nordic NRF 52832's NFC hardware.
If I wanted a simple...
Hey there faced with the following problem:
I have two hardware setups:
1. Laird DEVK-654 (nrf52480) without external oscillator
2. Laird BL654 mounted to a carrier...
I added the Generic OnOff Model from the thingy52-mesh-provisioning-demo to the Light Switch Proxy Client example from the nRF5_SDK_for_Mesh and get a linker error for the...
Hi All, I am polishing the code that we have, working out minor bugs, etc, we use Nordic UART to exchange data between our device and smartphone or tablet, sometimes data...
What is the proper way to temporarily disable the softdevice? Currently I have the following
sd_ble_gap_adv_stop(); bool disabled_softdevice = false; if (nrf_sdh_is_enabled...
hi ,
We developed a BLE slave device with NRF52840.
Well, we are doing product certification, BQB CE FCC, etc now.
One of the items is the 2m rate test, and we want...
hi ,
We developed a BLE slave device with NRF52840.
Well, we are doing product certification, BQB CE FCC, etc now.
One of the items is the 2m rate test, and we want...
Hi nordic members,
I am using nrF51822 board. I want to inform you that i am getting error undefined symbol: __data_start__ at compile time in segger embedded studio for...
