I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
I am using a module MS12SF1(nrf5340 + nrf7002). I wanted to perform dfu over ble by using nrf7002dk_nrf5340_cpuapp_ns or nrf7002dk_nrf5340_cpuapp build configurations but...
Hi, i am trying to port my project based on the matter light bulb sample to a PAN1780 module which also uses the nrf52840 I used before.
When building I receive this error...
Hi, I'd like to trace the Bluetooth behavior of the nRF Desktop sample post-pairing. I have an nrf52840 dongle running the sniffer, and can observe advertising packets. Could...
Hi
We have a legacy product with around 100.000 active devices. We still need to distribute new firmware releases, and we are using the "Chained DFU" app for this purpose...
Currently, my environment uses a mobile network shared through a wired connection to an RT-AX57 router. I am working in the VSCode environment using SDK v2.6.1. Devices: Nest...
I am trying to connect a nrf5340dk to a Jetson. For now I am testing with an Arduino. I am trying to run the CanCounter example with a device tree overlay file. Also I would...
Hi,
I tried to implement the CAF LEDs module as described here . But when added the Kconfig variable CONFIG_LED_PWM =y I got the error message "CONFIG_LED_PWM was assigned...
Hi,
I was developing on Visual Studio Code earlier, and for some reason, I cannot build pristine. If I try to edit the build configuration, it never loads, and if I try...
Hi,
we are trying to make the NORA-B126 (specifically its onboard LNA) work with nrf sdk 2.3.0 by modifying the 5340dk dts and defconfig files as specified in the NORA-B1_SIM_UBX...
Hi there,
I'm working on NCS2.7.0 and nrf52840.
I used the chip-cert to generate custom DAC, PAI, and PAA with VID = 0x1234 and PID = 0x5678, then placed the...
Hi there,
Thanks for helping. We are using the nRF52840 DK along with the Power Profiler Kit 2 (PPK2) for power measurement. We are encountering periodic power spikes during...
Hi, we are designing a factory acceptance test (FAT) jig for a custom board containing an NRF9160 SiP. We are testing more than one thousand boards, and probably more than...
Hello
We are using a slave processor with AT command to communicate with the nRF9161 . This is working without problem
But we are initially using the Quick Start 0.2.7...
Hello,
I'm using nRF9160 as a HCI host and nRF52840 as HCI controller (nRF52840 config is based on HCI lpuart example). My application receives data over Bluetooth using...
