hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello,
We are developing an application to work as a multilink central with 3 different kind of BLE devices that include 1 custom device which advertise customised NUS...
I'm attempting to add support for a custom ili9341 display to a project running on a the uBlox Nora dev kit. I'm currently using VS Code with nRF Connect SDK1.9.1. My question...
tried the proximity example to check pairing/auto-repairing using PCA10040 board. currently having not auto repaing after we power OFF/ON the device.
we are planning to...
Hi,
I encountered an error when I turned on NRF_LOG_BACKEND_RTT_ENABLED in a project:
"...section '.log_backends' will not fit in region ‘UNPLACED_SECTIONS’."
"region...
Hi All!
I am using nrf21540 along with nrf52833/20. My question is can it be possible to use nrf5 SDK instead of NCS? I have developed the application using nrf5 SDK and...
Dear nordic team,
we are successfully communicating our old nRF2401 shockburst design to a nRF5340 board; except for the CRC.
The challenge: the nRF2401 shockburst allowed...
Hello,
In function such as i2c_write and i2c_read does Zephyr check to make sure the device is not a NULL pointer? If not how would it react if it were passed one?
...
Hi,
I tried to run the "matter" light_bulb example from nrfconnect versions 2.0.0, 1.9.1 2.0.99, but failed to
to see blinking LEDs. I suspect this may have something...
Hello dear Nordic. I am reading your documentation and stuck on the following issue:
According to the SEQ[1].CNT register there are 3 pulses with different duty cycle...
Hello there,
The same code works reliably on dev kit but not on my customized hardware. By cutting the 32k external crystal jumper on the dev kit, the same failure can...
Hi,
I am working on nRF52840 dongle.
i am facing a issue with programming. before it i was trying to do it with arduino. i don't know its bootloader gets disturbed....
I build the asset_tracker with custom code added to it and working well. The build time messages are shown in the attached text file. There e %of Flash used in show thrice...
HI,
I'm trying to configure the MCUboot / Netboot with an external QSPI flash. I can do it for the APP core with MCUboot, however I get lost how it work with the NET core...
Hi Nordic team
We plan to develop a stereo bluetooth loudspeaker, that can be connected from any smartphone to stream audio.
The prefered audio output would be PWM since...
