I posted another question along these lines, about using the Timeslot API to get observer behaviour with the S110 v7.0 SD, but I am having trouble getting it to work.
Are...
I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
after connect v3.7.1 programer v1.4.11 for a nrf9160dk I get an error "Error: Error occured when get library info. Errorcode: CouldNotOpenDevice (0x4) Lowlevel error: INVALID_OPERATION...
I have followed the tutorial of nRF5340: Network core bootloader to test the bootloader on app. core & net core.
I chose to use VS code to develop.
I am successful to...
Hi.
Simcom SIM7000 series datasheet recommends the following schematic:
Simcoms SIM800C module datasheet recommends the following schematic:
Quectel BG96 module...
I currently use an NRF52810 to write a firmware in an external flash, then an STM32 will read this firmware and download it in its internal flash. The communication between...
Hello,
I tried to read the value from bq4050 on smbus.
I had good results but I got wrong value randomly as following.
The last marked value is temperature from DAStatus2Reg...
Hello, I am developing a custom firmware for NRF52832 controller. I have develop power saving mode using power manage function. Also I have enabled interrupt inside code and...
hi,In SAADC sampling, the upper limit and lower limit of sampling results are set. Interrupt events are generated only when they are less than the lower limit or greater than...
Hey Devzone
Running into an interesting issue with the .zip files on http://developer.nordicsemi.com/.pc-tools/toolchain/ . When I try to download in browser they fail....
Hi
I am using nrf51422 (on the DK) with S130, SDK12, functioning as a central, reading multiple peripherals (which I also programmed),
Some of those peripherals have manufacturer...
Hello, With reference to Case ID: 278209, I wanted to include a driver file, for which I was suggested to add the label/variable "zephyr_library_include_directories(.)" in...
Hi,
I have a strange problem.
When I connect the jlink and battery power on board at the same time,and download the application, it works normally. But when I disconnect...
Good morning.
I have a custom board with softdevice 132 and sdk 15.0.3 where I have configured pin P0.16 and P0.17 for uart (rx, tx). I have read in other posts/problems...
I have written BTLE code that works on the nRF52840 DK using SoftDevice s140. I have ported this code to work on the nRF51 DK and nrf51822 MCU using SoftDevice s130. I use...
Hi all:
on my project,i set
define NRF_SDH_BLE_PERIPHERAL_LINK_COUNT 1
define NRF_SDH_BLE_CENTRAL_LINK_COUNT 6
on my peripheral , i need mtu = 185
on my central...
