Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
I use pin SDIN, SCLK, CS, DC.
but how do I connect the pin nrf51822
spi_master_example is
#define SPIM0_SCK_PIN 25u /**< SPI clock GPIO pin number. */
#define SPIM0_MOSI_PIN...
I have been reading about code regions in the nrf reference manual and understood about CLENR0 and how to use it. I have however, two questions
What is Pre Programmed...
I am using the SPI Slave port in the nRF51822 and am always transferring 20 bytes. No matter what I do, it seems that the status register in the IRQ says that I got a TX buffer...
I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hi,
I need to be able to communicate between two boards via UART. I had a look at the example from Ole provided here: devzone.nordicsemi.com/.../ as well as other references...
Hello,
I am wondering if I can use any 128 bit UUID value.
For example, in the example uart project, Nordic UART Service = 6E400001-B5A3-F393-E0A9-E50E24DCCA9E is used...
If I want to stream samples up to the nRF Toolbox HRM iOS app plot, what is the fastest that I can call ble_hrs_heart_rate_measurement_send in firmware assuming I have nothing...
Hi,
I'm using nRF51822 Development Kit and trying to program softdevice with nRFgo Studio. The file to program is C:/Program Files (x86)/Nordic Semiconductor/nRFgo Studio...
I'm using S110 version 7.1.0, but need a way to validate in general which S110 and which SDK version I have associated with this .uvprojx project.
Much of this stems from...
I'm running the ble_app_beacon_s110_pca10028 example on my NRF51 dongle. The good news is that I see a beacon transmission on my iPhone 6 on this "Pally BLE Scanner" app....
We are developing a new BLE tag product using the nRF51822. We would like to assemble the PCB and battery in a single operation then program the product sometime later. Can...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
I'm trying to use RTT for debug printing and having some trouble. I'm using the nrf51-ble-app-lbs example app that goes with App Note 36. I've added the RTT code from www...
