Moving from SDK version 5.1 to 6.0, the buttons on my PCA20006 beacons no longer works as expected. When I press a button, it seems to register the release of a button incorrectly...
I posted another question along these lines, about using the Timeslot API to get observer behaviour with the S110 v7.0 SD, but I am having trouble getting it to work.
Are...
I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi Networks,
I have tried to build the nRF5340 DK as a gateway.
Enabled
1. CONFIG_BT_GATEWAY=y
2. CONFIG_BT_GATEWAY_ADV=y
3. CONFIG_BT_GATEWAY_GATT=y
But not acting...
Hello,
I will be designing a board using with nRF52833 with the NRF21540 for the added gain. Would it be possible to add adaptive frequency hopping?
Thank you,
Shah...
The central device has the below settings
One central device A and two peripheral devices B and C, B and C have the exact same firmware. A can establish the connection...
Hello
I have implemented the stereo function to the nrf5340 audio application on SDK V2.6.0. i can send stereo audio signal to both of the two headset at the same time or...
Hi, I recently got nRF5340 Audio DK for my work. I have been try to use the onboard mic for collecting audio and transmit it via BLE, since I'm a newbie I couldn't do it....
Hi
I have successfully added the nrf_crypto files to the UART project. It compiles without any issue. Now I was trying to run the ECDSA example code in the UART project...
I used nrf52840 board with SDK 17_1_0
I used segger embedded studio IDE
i want to Implement two VL53L5CX TOF sensor with nrf52840 so i used two TWI,
but when i init...
Hello,
I'm migrating my project from using child/parent to sysbuild ( simple Hello world code, and using MCUBOOT + NSIB ).
The first error i faced when moving to use sysbuild...
Using Zephyr.
I'm looking for a process or a function to log unconditional message in the logging system including timestamp and other typical logging/display functionality...
We have a custom board with an nRF9160 directly connected to a SIM-S-IO3-MFF2-2 IC. I understand these kinds of eSIMs in IOT devices are typically provisioned over-the-air...
I have a slightly off the wall requirement where I need to send a serial data stream at 5kbps, it will be used to drive an external OOK 433MHz transmitter. The data format...
Hi,
I am having some issues when trying to enable the Fast Pair when executing the bt_fast_pair_enable(). I used the debugger to determine where it's failing:
...
Hello,
I am working on setting up the nrf52 (nrf52832) to communicated with the AD4130 from Analog Devices via the SPI Port. However, I am encountering a problem that I...
Hi,
I'm using the nrf9160, sdk 2.4.0 and tool chain 2.6.1. I need to scan the i2c sensor, I didn't find the i2c scanner example. So i was add one code and tested i'm getting...
I am trying to test the light switch and light bulb example with google home app and google nest device as a border router. I have flashed the bulb example into a nrf52840dk...
