Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Our device connects to a cell tower and then creates a socket to our gateway. I monitor +CEREG to see what it goes through to connect to a cell tower. Below is the meaning...
I testing UART0 data transmossion. But, could resolve why CPU resets when executing : if (!nrfx_is_in_ram(buf)) in uart_nrfx_uarte.c file. See atached image, where Reset occurs...
I am developing a custom board with an electronic paper device (EPD) attached, which will be controlled with SPI and a five additional GPIOs (a mixture of inputs and outputs...
Hi Guys,
I have a nRF5340-DK(PCA10095) here and I'm planned to perform some BT-SIG RF testing with it but I can't find the proper hex file for DTM(Direct test mode) setup...
I (think I) have successfully located the code responsible for handling the data received BUT! The code segment:
in app_uart_fifo.c
seem to only receive a paltry 1...
Hello
I want to measure Low power current in nrf52840-DK with System ON mode.
I need to know how much current consumes by nrf52840 SoC while I2C Engine ON, SPI ON, and...
Hi.
I am working with the nrfConnect SDK 1.8.0. I would like to configure the nrf5340 for maximum throughput to work as a server for a smartphone device.
How should...
Hi all,
I am using NRF52840 and I am saving some data to the flash memory using fds. The data are 216 bytes in each file and there are 3400 files which is in total 734kbytes...
Hi,
In my application, I am writing in flash.
But when I do so, my openthread data in flash gets o verwritten, the node doesn't retain its commissioning data.
In nrf_SDK_For_Thread_and_Zigbee...
Hi All ,
I am using nrf9160Dk ,When i use asset tracker V2 i successfully get the GPS values on the nrf Cloud . But when i use the Asset Tracker only then i am unable to...
Hi there,
From the product specification of the nrf5340, we can only find UARTE peripherals (UART with EasyDMA). Is it possible to implement uart without DMA? Of course...
Hi
I was just curious as to whether or not there is a specific reason the Xenon's PWM capabilities are not available with NCS/Zephyr. Is there a hard limitation or is this...
Hi Team,
SDK - 17.1.0
chip -nrf52810
I want to store sensor data (12 bytes) every 30 seconds in flash memory. Once the flash is full, I want to replace the old data...
I'm trying to interface with the ds1339 real time clock to set and read the time for timestamping tasks in ncs 1.8.0. I've found a few tutorials that boil down to:
1....
