Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
My board is nRF5340Dk with NCS 2.6.1 and toolchain 2.6.1.
At this development stage I want to measure continuously incoming frequency ranging from 1Hz to 1MHz with high...
Hello,
I have a scenario where I use crashlog but not flashlog.
My application is crashing in nrf_log_backend_crashlog_panic_set during log_msg_queue_process(mp_flashlog_queue...
Hello
I was working on a project, trying to enable the power management but I could not. So I just tested the simple zephyr sample application device_pm just to see if there...
Hello. We are testing the example of bl provisioning provided by sdk v2.8.0.
When the first wifi is connected, the wifi's data is stored on the board, and even if you turn...
Hello Nordic Team, I am working on a LE Audio project on NCS v2.9.0. My development board is nrf5340-dk. I am using unicast client example and I am trying to use it with my...
Hello,
In nRF Connect for Mobile, custom UUIDs show up as unknown, making it difficult to identify them easily.
Is there a way to add custom UUIDs, as can be done for...
Hello, I have recently switched to nrf52840 dongle for 802.15.4 sniffing.
I did a simple test with a ZigBee Green Power sensor sending data on channel 11. On the receiver...
Hi,
I am using a nrf52840 dongle for sniffing the bluetooth connection between 2 devices. These are the wireshark logs
What I could see is it initiates the pairing with...
I have a custom board with a nrf9160 on it that has been working for the last three months but last week when i was evaluating low power modes on the board i couldn't talk...
Hi,
i am using SDK version 2.1.1 and recently we had a problem due to the errata 160 which is fixed also in SDK 2.1.4
I am using Toolchain Manager 1.5.3 and i cannot select...
Hi,
we plan to use the nRF52832 in a new project, where we will need ANT support.
I've seen that it is possible to use the nRF5 SDK and the SoftDevice 332 to have ANT...
Hi everyone, I have a problems when I build custom board NRF54L15. I build this project for custom board for nrf52833. It's okay and no error. After that, I change this board...
Hi!
I am testing the nRF54L15-DK with 2.9.0 SDK and have some questions:
1. MX25R64: - why is it used in 1-bit (spi) and not 4-bit (qspi) mode? - OTOH this setup saves...
