I posted another question along these lines, about using the Timeslot API to get observer behaviour with the S110 v7.0 SD, but I am having trouble getting it to work.
Are...
I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
Hi
I have been studying the nRF Connect SDK and taking the courses at Nordic Dev Academy. In the Zephyr Fundamentals course, as I don't have the sensors used in lesson 6...
hello.
We're now planning to migrate our firmware library from nrf5 sdk 17.1.0 to stand alone nrfx v3.xx.x.
All our products are made with nrf5 sdk 17.1.0 using ses. ...
I’m using a custom PCB based on the Minew ME54BS01 module (nRF54L15 SoC) for both ends of our proof‑of‑concept: one node as a GATT‑based Channel‑Sounding reflector (leveraging...
Hi,
I am trying to port the DTM example to our board, 52833 based but when DTM is initialised I get about 1400ms of CW then:
00> *** Booting nRF Connect SDK v2.5.2 **...
I am unable to detect any i2c device when connected to the Nordic nRF54L15 DK kit. I have change the voltage from 1.8v to 3.3v and Tried and explore other pins in Port 0 and...
Hi everyone,
I'm working with the nRF9160 and trying to configure P0.19 as the UART TX pin using Zephyr. Here's the configuration I used in the device tree:
uart1_default...
We need to set a GPIO pin in MCUBoot to activate an external USB hub chip so the USB DFU will work. I would like to do this with code in our project rather than directly modifying...
I'm working with the nRF7002DK board using NCS version 2.6.0 . The internal flash is full, so I need to perform BLE DFU using external flash. Is there a sample available for...
Hi,nordic team
Iam programming with nrf52833 and ncs v2.9.0
I am doing DFU by myself.And I Flash_write data into slot1_partition,I am sure my data write in flash is correct...
How can this be done?
calls to bt_id_reset, and bt_id_delete do not work on the BT_ID_DEFAULT.
I wish for the device to appear as a different device (IRK) each time it...
Hi all,
Actually I'm building with vscode my firmware for a custom board build with an nRF9151 non secure. After building I got a merged.hex file, this is the file upload...
Using nrf sample from v2.9.1/nrf/samples/crpyto/rng Configure build with v2.9.1 SDK/Toolchain Configure build with board target: nrf5340dk/nrf5340/cpuapp Add MCUBOOT support...
Hi, our company is currently using nRF52832/RSSI feature to provide simple asset tracking/location service. Would like to know if we want to improve the accuracy by using...
Hi, we're creating a BLE mouse. We've setup the HID service- clicking button 1 on the nrf52832DK sends left mouse button click- nothing else is being sent. The problem: even...
I've seen other threads about the issue:
- https://devzone.nordicsemi.com/f/nordic-q-a/117267/light-bulb-sample-works-on-nrf52840dk-and-doesn-t-on-nrf52840-dongle
- https...
