Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
When I use Windows nRF Connect to connect nRF52832 device. It pop up window for user to enter passkey. But When I use iOS nRF Connect to connect nRF52832 device. It doesn...
I am trying to implement spi in my project and have encountered an issue where the delay from chipselect to sclk is around 10 us which should be as low as 1us according to...
I have been developing my code on NRF52840 based on nrfsdk v1.7. Since keil free version has a limit of 32kb i am moving my code to VS code. VS by default adds 2.0 latest...
Hi,
I'm testing maximum tx throughput.
I'm using ble_app_hrs example and mcu is nRF52832(s132). (sdk : 16.0.0)
The goal is transmit data at 96Kbps.
I read that the...
Dear Members,
We have 2 ANT receivers and 1 ANT Speed Transmitter, (Bicycle Speed Cadence) , Garmin GSC-10,
Is it possible ? Looks like one receiver gets a good value...
Hi,
I am using NCS v2.0.0, VScode with "nrf connect for vscode v2022.7.242".
I can't build any samples with MCUboot, by enable CONFIG_BOOTLOADER_MCUBOOT =y.
The build...
The following error occurs when I plug in the USB cable to burn the firmware，This is an interesting bug: it usually fails on the first burn, but succeeds on the second or...
Hi everyone,
I am new to nRF52833, and trying to learn it with some tutorials. I am following this tutorial.
You can download my "examples" file from here . You should...
Hi,
Can you please provide some sample code for sending data to Tm4C using ble_app_uart in VScode and also tell me which function I need to use for sending some data from...
When I use Windows nRF Connect to connect to nRF52832 device. It pop up window for user to enter passkey. But When I use iOS nRF Connect to connect to nRF52832 device. It...
HI, I am start use NRF52840DK(rev3) to devlopment usb application，but jlink always show this information
I try to use 'nrfjprog --recover' to disable read protection,...
Hello Groups,
I'm trying to send I2C/twi data from nRF52832 using the Nordic development board with nRF Connect SDK 1.9.1.
Based on the sample project ble_app_uart, I...
Hi nordic:
As shown in the figure below, I see that the BLE protocol standard mentions the ScanReq backoff mechanism. Does NORDIC implement it?
jermi.jin
thanks!!...
Hi,
The central_uart sample hardfaults when bt_enable(NULL) is entered. I can use the debugger and step over the first couple lines but stepping over bt_enable causes a...
