Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
Hi, I'm developing an application based on ble_app_uart, and integrate FOTA is the last feature. I'm using sdk16, S140, nRF52833. I plan update firmware over BLE, so I have...
We've a custom board which has NRF52833 and TM52F1376-MTP-C3. They are connected over UART.
What I want is transfer binary data between Phone and nRF52 over BLE.
and then...
Hi Nordic team,
I'm going to start new BLE application project, so I tried to understand how to use nRF52 series first.
I completed the academy and I'm trying to make...
I am attempting to compile the peripheral_uart example targeting nrf52840dk, I've done quite a bit of work with zephyr but never with the nRF Connect SDK. I've encountered...
Dear Nordic,
There is an issue with simultaneous RTT shell and logging on nCS 2.0.0, please check the screenshot.
Althougth CONFIG_LOG_BACKEND_RTT_BUFFER=1 setting is...
New to Zephyr it has been reasonably straightforward building the UDP sample application to enable an nRF9160 dev board to send and receive UDP messages via NB/IoT to/from...
1. I want to run asset_tracker_v2 in thingy91 kit.
2. I want to interface two UART external devices to thingy 91, may the pins of nRF52840 be used ? if yes, in asset_tracker...
I followed this page in the section "Program application using nRF Connect Programmer", and tried to program my nRF5280 Dongle in Windows.
Like below, then I clicked "Write...
Dear Support Team，
I downloaded the code from github.com/.../ble_app_uart__saadc_timer_driven__scan_mode , modified the file, and burned it to 52832. After running the program...
Hi,
we need a firmware for the nRF52840 to do a function test for the EMC approval test. The test must show that the BT connection still works. It should also show if the...
Hi! I am using the following setup to run the "ble_app_uart" example:
nRF5 SDK 17.1.0
BMD 360 EVAL Board (nRF52811)
SEGGER Embedded Studio V6.32a
I selected the...
Hi ,
I am using BMD 330. Able to flash my working code using Segger.
Post flashing it gets into a loop in the following code
<sym_PAD7XREQQORPXRJMXMW2EYVS4S43S42A5D43SBA...
Hello,
Every time I restart the power(power on reset) and then use the command nrfjprog to download, the following error will appear
After I use the nrfjprog --recover...
I have read that you can save RAM with the newer implementation, so I decide to go ahead and change my code. The SDK 16 migration guide says:
< To replace app_timer v1 with...
