Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
Hello everyone,
I am using the fanstel BC840, where the tx and rx pins of the uart are alloced on 1.02 and 1.01:
So i have created a custom_board named hello_board...
Hi,
I’m trying to test/confirm the accuracy of the 32kHz crystal oscillator and the 32MHz crystal oscillator by toggling a GPIO at a derived rate and at 50% duty. But I...
The tag options did not include just nRF Connect as an option so I picked something that had nRF Connect in it. This issue has nothing to do with the SDK.
This is a question...
Help me simple LED Blinkink nrf51822 AA type i'm using YJ-14015 and stlink compiler.. i'm also using keil for IDE. i don't know how to create program and setting for compiler...
Hi,
Using nrfutil tool to transfer firmware package on Windows 10 system is much slower than on NRF toolbox on Android phone. How can we improve the transfer rate of nrfutil...
Hello, when trying to program a custom board with an NRF52805 with a J-Link from SEGGER Studio using one of the examples for the board "nrf52dk_nrf52805", I get an error saying...
Dear Devzone,
At the moment, We do not have methods to measure the GPS sensitivity of our products based on nRF9160.
We are using an active antenna with LNA gain 16dB...
We are using the NRF52 as a SoC in a sensitive analog application,
I need to model power supply noise created by the DCDC convertors REG0 and REG1.
Is there a SPICE model...
Hi Nordic team,
My dev environment is as follows:
nrf52840 + s140 +SD6.0.0 + SDK15.0.0 + SES + nrf52840-DK
Here, nrf52840-DK is configured as BLE Central and my peripheral...
Hello,
I'm trying to develop a ble-uart gateway based on mesh provisioner and peripheral-uart samples but i'm getting an error on getting the device bind of the uart device...
Our original BLE stack application on the nrf52840 has integrated encryption. It uses LESC with MITM and bonding.
I have gotten a certain level of run time success with...
Hi, I cant get access to my custom nrf52840 board after I click "Erase all" in "Programmer" in "nRF Connect for Desktop". This custom board has been working with me for at...
Im 100% sure i import the file due to my config
../../../config;../../../../../../../components; ../../../../../../../components/ble/ble_advertising; ../../../../.....
Hi,
Is it possible to validate the value of a characteristic write operation and ignore it if it's not within my set parameters?
I.e. in the BLE_GATTS_EVT_WRITE event...
