Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Is it possible to set up an NRF Connect SDK project such that the firmware can be updated over BLE, without including the SoftDevice in the update?
I'm using NRF52810 which...
Hello,
i have searched for uart, i2c/twi communication with polling, interrupt, DMA method different brief explained guide for NRF52
but i have not found it any where...
Hello,
Previously, my nRF52840 DK worked perfectly fine through the USB (J2) connector. Then I successfully programmed PCA10059 by Debug OUT(P19) of the nRF52840 DK board...
My Android app allows the user to un-provision a mesh node. To do so, the app just sends a ConfigNodeReset message to the node's unicast address, which works perfectly if...
Hi, I want to add some auto-test capability to my nRF5340-based project. I thought one useful feature would be to measure voltage AND current at the hot node when all devices...
Hi all
We are switching to nrf-sdk v1.6.0 in our project and encountered a problem with MCUBoot.
The image builds successfully and can be flashed successfully as well...
Hi,
Iam using SDK 17 ,s140_nrf52_7.2.0_softdevice on NRF52840 SDK.For the first time I have noticed an issue,as below on running sample nordic17.0.2\examples\ble_peripheral...
I would like to use the Arduino Nano 33 BLE with MCUBoot and MCUMGR for FOTA. I am wondering if it is possible to use a two-stage bootloader (first stage Arduino BOSSAC, second...
I'm wondering whether the value pointed to by "ble_gatts_hvx_params_t.p_len" passed to sd_ble_gatts_hvx is copied to SoftDevice-owned memory before the call returns NRF_SUCCESS...
Hi,
I would like to create a library for the Nano 33 BLE to be able to use the NFC features that are available via the nRF52840 chip.
I am aware that there are some examples...
I'm starting a new product development using nRF52832, SDK 17.0.2 and softdevice S312.
Should I use v6.1.1 or v7.0.1 of S312?
Nordic's docs for SDK 17.0.2 state that S312...
I have no idea about how to read the device id of the external flash in the nrf52840dk? Please guide me to do so.
I also referred the MX25R6435F datasheet, to see the method...
According https://infocenter.nordicsemi.com/topic/ref_at_commands/REF/at_commands/nw_service/xrai_set.html control plane data only are supported.
How to set PDN to use control...
Hello, I need a reference PCB layout for the nRF52810-CAAA WLCSP-33 chip. There doesn't seem to be a reference layout for this specific chip. Furthermore it differs from the...
