Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Currently, we are developing our own board with NRF5340-CLAA. It does not have a 32.768kHz crystal oscillator, only an external 32MHz crystal oscillator. We have applied the...
Hello, I need to do some RTT trace logging, but I can’t enable it. I am trying to create minimal example code, and for this purpose I am using the UDP sample. I added these...
Hi,
We have a working firmware that uses LTE-M for network connectivity to connect to NRF Cloud. But upon testing with NB-IoT configuration (CONFIG_LTE_NETWORK_MODE_NBIOT_GPS...
Hello, the time to ask for help has come again... I keep hitting a crash in my BM833 code related to "Illegal use of the EPSR". Code is fairly simple and supposed to be pretty...
Hi,
hi have the same problem related here: https://devzone.nordicsemi.com/f/nordic-q-a/91890/nrf52-reports-two-jlink-cdc-uart-ports
With revision 2, UART show only one...
We are looking into a device using the NRF54L to do low power indoor tracking since it has a very low power consumption when using the RADIO peripheral.
We see that the...
Hello,
I am facing an issue with nRF Cloud device provisioning. I am using the nrfcloud-util tool to provision the device to nRF Cloud (as recommended for production provisioning...
Hi all,
I’m running into issues flashing an Arduino Nano 33 BLE Rev2 (nRF52840) using Zephyr and the bossac runner. I consistently hit a “Flash erase failed” error and can...
Dear Nordic,
We’ve developed an application which runs on an nRF9151 DK using NCS 2.8.2. The device is running modem fw nrf91x1_2.0.2. Our application has enabled modem...
Hi I made a small production run of boards using nrf9151 where a handful of them have issues with nrf9151 such as not being able to flash. How do I debug the circuit at the...
Hi, I have a simple question. Is it possible, during the execution of Channel sounding ( ras_initiator ), for the initiator to regularly obtain the current RSSI from the reflector...
I am trying to flash an application image in nRF9160 on Thingy91. Thingy91 is in MCUBoot mode, and the selector switch is on nRF91 position. I get an error as below if I try...
Hello,
I am facing an issue building the NCS v3.1.0 Matter light bulb sample for nRF52840-DK:
cluster-enums-check.h:151:10: fatal error: clusters/TotalVolatileOrganicCompoundsConcentrationMeasurement...
