I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
The Nordic SDK provides headers for a finite state machine, queue, ringbuffer and other utilities in the 802_15_4 library in nRF5_SDK_17.0.2_d674dde/components/802_15_4/api...
Hello,
I'm developing firmware for nRF52832 with FreeRTOS, I would like to use TWI to access to an external memory. Every time I try to use "nrf_drv_twi_tx" function i get...
Hello,
Is it possible to get more information on how the NWK Frame counter is stored in NVRAM. I can see fragments of code from zb_nrf52_nvram.c I see that it uses nrf_fstorage_write...
I am facing an issue in writing data to a register of my bmp388 sensor using I2C.
If I fill my transmit buffer of 2 bytes in following way , tx_buf[] = {register_address...
hi support team,
i was testing this this example " http://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.4.0/nrf/samples/nrf5340/netboot/README.html#nc-bootloader "
i...
Hello all,
We are trying to implement coexistence between BLE and Bluetooth mesh.
After following the Nordic coexistence tutorials, our program builds fine using both...
I have worked with the nRF51822 and the nRF51 DK and used the pc-ble-driver on the nRF52840 dongle. Now all I am interested in the BTLE development, not mesh. I found out...
Hi
I did some experiments with the GATT capabilities of the S140 7.2.0 softdevice. An experiment that I did showed a behavior that is not as I would expect it.
Steps to...
hi professor,
I use the zephyr spi driver to control spi nand flash.I want to send two bytes and read 3 bytes. But between write and read time sequence there are 10us delay...
I'm testing nRF Mesh on nRF52840 chip, I used P1.10 for LNA pin and P1.13 for PA pin, I tried to config but it not worked. how to fix it?
static mesh_pa_lna_gpiote_params_t...
Dear support team
Please note my sample application code attached, and the trace of the I2C transmission
I am facing the issue that the twi driver does not write more...
Now I am using nRF52840 I want to get data from a sensor via SPI. I configured the SPI pins like this P0.11 -> SPI_CS P0.12 -> SPI_MOSI
Actually, I couldn't get any data...
Hi Nordic-Support,
I am trying to figure out how the boards in ncs/nrf (e.g. thingy91_nrf9160) are made available for applications. I cannot see how they are added to the...
