Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hello. I am reading up on documentation regarding measuring current on the nRF54L15-DK with an ammeter. I do notice that when we set up the board, we need to use the 2x5 SWD...
Hi there,
I attempted to change the nRF54L15-PDK settings in Board Configurator. I disabled VCOM0, VCOM1, Power to LEDs, Software Debugger and set VDD to 2.0V. I have...
Hi all,
I am working on nRF-9160 and nRF-9151, and I wanna know does Serial LTE Modem support will message function for MQTT connection or other connection?
I've asked...
Hi,
I am not familiar with the 9160DK board. I followed the same steps as the nRF Desktop Connect application guide but it always shows verification failed. I am using my...
Hi
I'm having an intermittent connectivity issue with the nRF9161 where after days of operation the device loses cellular registration and fails to reconnect.
The...
Hi,
is there a way to hide the west project from the Git view in VS code? Sometimes you just don't need to view any changes related to west and it's getting quite messy...
I am working on a Zigbee network using the nRF Connect SDK and need to retrieve the link quality information (LQI) of a specific device based on its short address. What ZDO...
Hi,
I have used nordic documentation a lot few years ago, and I am looking for BLE sequence diagrams especially the ones during pairing process with LE Secure connection...
Good morning,
currently we are on ncs SDK v2.7.0.
Because SDK v2.8.0 supports the KMU in MCUboot on the nRF54L15, I updated immediately and gave it a try.
Unfortunately...
Hello,
I searched but I can't find how to retrieve accelerometer data with thingy:53 and then send it via bluetooth to nRF Connect on phone?
Can you help me
Thank...
Hi,
I have opened sample "Peripheral_hr_coded". I have build it successfully. I click on debug. I expect cursor would start from Main function. But Debug was not started...
I'm developing my application using the NRF Connect SDK in VS code. SDK Version 2.4.2. The NRF52832f we're using is integrated into a module made by fanstel and it has been...
Hi,
I am going through the DevAcademy Bluetooth LE lessons, using nRF5 DK. But I run into problems directly in the exercise of the first lesson. Everything goes fine to...
Hello Nordic community,
I am currently working on developing applications for Matter over Thread and have set up my ZAP file accordingly. I've successfully flashed two types...
I want to use a switch in the overlay file, like:
To do so, I try to add a config statement in a custom KConfig file. (mp_Kconfig.conf):
Adding the file to the build configuration...
