I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Dear Nordic Team,
We are working with the nRF52833 using nRF5 SDK 17.1.0 and have implemented OTA DFU in our application.in OTA We have merged all firmware components...
Hi,
After installing nrf sdk v2.9.3 trying to build application under Windows fails with the following message:
Trying to run any command inside the NCS shell/terminal...
Hello, We are building an application with NRF54 as the host MCU and NRF9151 as a serial modem. We are considering using a SoftSIM from Monogoto. Our main concern is how easy...
Hello everyone, I have a question regarding the LIS2MDL sensor. When I configure Register A, it correctly takes the value that I set. However, after the sensor initialization...
I am running smp_svr demo on my nrf54l15DK board, and use mcumgr command on my linux.
I could connect to my ble device and echo hello successfully (via peer_name='Zephyr...
The last years I have developed a lot software (low level) for the nRF52840. I like this MCU very much, especially the SHORTS-Registers and EasyDMA are powerful for real short...
I try to get the one button sample to work. There were several details missing to be able to compile and run this sample, which was very frustrating. After editing/updating...
Hello Nordic Team,
I am working on the nRF52833 using nRF5 SDK 17.1.0 and i have implemented OTA DFU in our application. in OTA We have merged all firmware into a single...
nRF52832: Multi node wireless LED synchronization via proprietary radio (nRF5 SDK 12.3.0 on PCA10040)
Summary This post shares a simple proprietary radio demo that synchronizes...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi all — I'm developing a custom nRF5340 development board (Raytac MDBT53-1M) and would value the community's honest read on whether it's worth producing.
The goal is...
I am developing a custom board using the nRF9151 module controlled by an external host microcontroller. The nRF91x1 is running the Serial LTE Modem (SLM) application.
In...
Hi,
I'm using nRF5340 + nRF7002 for project that use wifi but I have issue while reading the default MAC before recording a new one.
The products are tested inside a...
When debugging the exercise 1 application from `Lesson 2 – Reading buttons and controlling LEDs` of `nRF Connect SDK Fundamentals`, I cannot set a breakpoint wherever I want...
