Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
Hi,
I have read the PPK2 user guide here https://docs.nordicsemi.com/bundle/ug_ppk2/page/UG/ppk/PPK_user_guide_Intro.html and the nRF 52833 DK here docs.nordicsemi.com/...
Same problem as , which was 3 years ago...
Our app builds fine until we enable MCUboot, when we get the above warning, and being good people we have CONFIG_COMPILER_WARNINGS_AS_ERRORS...
Where can I find expected throughput for coded PHY in real life? The bitrate for S2 is 500 kbps because there are two symbols per bit in respect to 1M PHY. As part of a packet...
Environment: SDK v3.1.1 with a custom board based on the nRF52840.
I wrote a test application that I've been using to verify the hardware on a custom nRF52840 board. I have...
Hi,
We are using an nRF52832 in a bare-metal project. (No SDK)
We have three input channels to the ADC that we wish to use. These must be oversampled. (256x)
To simplify...
Hi guys,
I'm trying to do FOTA updates on my board and I was able so far to download the image but not able to apply it.
I've followed the academy FOTA over WiFi example...
I've got an example code to turn on an LED with a button, it works. When I change it to send an spi command, it doesn't work anymore.
Could you check if you see something...
Using;NRF52832,
SDK17,
Flutter 3.10.5 ,
nordic_dfu : 6.0.1,
iOS 16.5.1
iPhone 14 Pro Max
Using my developer device I can successfully update DFU,
However on...
I flashed the same code to the two nrf5340dk but i get the below output , with out any changes in the example sample code. it gives the serial output every time E: IPC endpoint...
I have installed both sdk 3.0.0 and 3.1.1 but both of them give me the following issue:
Upon building, the error given above shows for some reason but this is not my own...
Hi,Team,
I am currently using the nrf5415 to develop OTA. My NCS version is v3.0.2. Now I have two types of devices: Hub and Terminal. Both of these devices use nrf54l15...
The uart output of nrf52840 dongles is corrupted, including no lines separation, strange characters. for example:
5E0 to 1:00000000148A0C90 [18FF] [UDP:�]�8~~[fdbc:dc24...
I first noticed this when incorrect flags reported by mcumgr when performing network core update
When performing a network core update with CONFIG_SECURE_BOOT_APPCORE enabled...
Hello, I am currently debugging with nRF52833 and nRF5 SDK, and I have a few questions to ask:
I want to time-share the BLE function and the ESB function on a single MCU...
