According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hello,
I'm trying to get a TIMER triggered ADC read on P1.11 AIN4. Sample advanced_non_blocking_internal_timer sounds like what I want but it isn't NRF54L15 compatible...
I am designing a very-low-cost device based on the nRF9151 and would like a quick technical clarification.
My plan is to power the SoC and all GPIO rails from a single 3...
I'm working on a project were we require the use of a custom OOB key (not generated by the device itself) and LESC.
We have both the central and peripheral device to configure...
Hi ,
Our nRF52840 chip is drawing a high-current burst of about 1.5 seconds during the DFU upgrade. Because we have a 10 mA current limit on the battery, the system browns...
Hi
According to the errata at https://docs-be.nordicsemi.com/bundle/errata_nRF21540_Rev2/attach/nRF21540_Revision_2_Errata_v1.2.pdf?_LANG=enus, a 33k resistor is required...
Hi,
I'm using nrf52840 in revision 3, which has protection access port enabled by default.
My application is built with SDK15.0.0 / SDS S140 6.0.0
In order to get debug...
Hi,
I would like to receive notifications from iPhone to nRF54L15-DK over BLE. Anyone in the nRF community tried iOS notifications over BLE to tell me how it is done please...
Hello,
Current Situation
We are working with an nRF5340 device running nRF Connect SDK v2.7.99-cs2 . BLE security is configured for Just Works pairing (Security Mode 1...
Dear Nordic Team,
I am using NRF54L15 on NRF54 DK board and when trying to use/activate any other UART other than UART20 (e.g. UART21, UART22, UART00) on my project, every...
Hello, I've been developing an nRF52840 on a custom PCB for ~1 month now, and my environment was working previously. After updating my version of Jlink and installing other...
Hello.
I'm using nrf9151 with nRF Connect SDK v3.1.1 and Zephyr v4.1.99, modem firmware v2.0.2 I try to implement the full modem update. After downloading the "firmware...
Hello,
I can no longer use AT commands on my nRF9161 DK development board.
It used to work perfectly, but I don't know what happened.
I had previously completed the...
Hello,
I wanted to see if it is possible to move provisioned devices between team IDs in the NRF cloud. Right now I am using a nrf9151 to connect to the cloud. Once the...
Hello,
I am using Nordic nRF Connect SDK v3.1.1 and nRF5340DK board.
My project is based on the project: GitHub - nordic-auko/nRF5-ble-timesync-demo: nRF52 clock synchronization...
