Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
I am using nrf connect SDK toolchain version 3.1.1 and nrf connect sdk version 3.1.1 , By default I don't have zigbee related samples/examples and also zboss stack library...
The original question was: "The nRF52840 PS mentions, that this chip contains an ETM but it does not mention the implemented version."
Researching the topic more, I found...
Hello Team,
We have noticed a very weird issue with the nRF5340 Audio DK. After flashing the audio application code given by nordic, everything works perfectly fine. No...
I have asked if I can post this request, ticket number 354361.
Can you help with new research on secure boot?
I am a cyber security researcher at the University of Bristol...
Hi there
I have a question about the way the nRF52 radio handles on air addresses. I currently am developing custom software that uses the nRF52810 radio for a custom protocol...
I’m working with a Manufacturer-Specific Cluster (Attributes) in the Matter Template sample from NCS SDK v3.1.1, and it works fine with attributes. However, when I try to...
Hi, We designed a board using NRF5340-CLAA-R by following the Altium Reference design. Although when we tried to place an order with JLCPCB or PCBWAY, then informed that they...
Hi, I am pretty certain I have used RTTViewer before on the nRF9160, albeit not frequently. I cannot remember if I only used it on custom nRF9160 boards or if I used it on...
hello,
on our bm833 dev board, I scope (using a PIO) the time it takes for the bt_nus_send function to send 146 BYTES. The PIO goes to 0 after the callback nus_sent_cb has...
Summary
We are developing a Central application on the nRF7002 DK (nRF5340 SoC) using NCS v2.7.0 . The goal is to establish and maintain 11 concurrent Bluetooth Low Energy...
We're working on a project that interfaces an nRF9151 with a BQ40Z50 from Texas Instruments (via I²C / TWI / SMBus), and we've noticed the communication is unreliable. The...
Hi,
We are currently working on power optimization and want the device to wake up from the System ON state ( PM_STATE_SUSPEND_TO_IDLE ) using the RTC0 timer. However, I...
Trying to prototype a pinout on the nRF54L15 dev kit. We want P1.02 to be a GPIO pin instead of NFC. We followed the instructions to recover the device which erases the UICR...
Hi,
I am facing the following issue when i am calling west build from gitlab runner.
west: unknown command "build"; workspace C:\ncs\v2.5.0 does not define this extension...
