Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi,
I'm using s140 trying to connect up to 8 devices to windows BLE adapter and BluetoothLEDevice object, I have 2 problems,
1- the maximum throughput with different configurations...
Hi All!
I am using Segger Embedded Studio and nRF5_SDK_v15.0.0 .Available kits for testing are nrf52833DK and rak4630(nrf52840).
We want to test nRF52833 support on long...
Both NRF were programmed thru USB NRF connect for Desktop programmer.
Both NRF are running the same soft properly.
To demonstrate the final look and put the dongle in...
Hello,
In my project i am using nrf52810 with my custom board for pushing data to UART so i have used UART example code for this but UART pins are connected 20 (TX), 25...
Hi
I'm working on a Zigbee network, and I want to have a few End Devices (ZED) connect to a Coordinator (ZC). And it's fine, I got that working by using the zigbee_default_signal_handler...
hi
i develop software with the nrf52dk, success with program it with nrf command line tool.
now i want to program the application on the nrf52 dongle but with no success...
I am trying to use SDK version 17.2.0 to develop a package (Boot Loader + SD + Application) for our product based on the PCA10040e board with an nRF52810 SoC.
I soon realized...
There is a serial interface in the nRF SDK that makes it easy to serialize mesh data over serial
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter...
Hello,
I am want to read Analog value from LDR sensor. I am unable to find ADC Input pin in nrf52840 Dongle datasheet but I got it in nrf52840 chip datasheet (page -576...
Hello Devzone Community,
I have a question set regarding correct, best way or ways to configure nRF9160 GPIOs for high impedance. My hardware is a custom board but shares...
I have the nrfConnect task that builds my project in vscode.
I need to add a script to execute before the nrfConnect task.
I added a task to my tasks.json but the task...
Hi,
Could you please tell me which firmware is flashed onto the thingy91 by default (both for the nrf52840 and for the nrf9160) ? Where can I find the source code for these...
Hello,
We are experiencing a strange issue when quickly turning off/on the NRF52840 on our board. In order to check whether the MCU wakes up correctly, a test fw was set...
Hi all,
If a client has only one root certificate, the servers that clients can connect to are limited. I want to provision multiple root certificates first and use them...
