Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
Hello,
nRFSD5 v16.0, softdevice v.7.0.1, nRF52840
We have an application where we receive data from mobile application whenever it writes to a certain UUID. The data is...
Hi...
How to read and write to the external flash
I am using sdk 15.2 version, interfacing the development kit nRF52832 with w25q64 external flash via spi. I have read...
Hi,
I have a Thingy:91 v 1.0.0 which runs fine with the provided asset tracker firmware thingy91_nbiot_dfu_2020-04-29_bc7ade8b.hex. Cloud connect also is fine.
I managed...
Hi Didrik Rokhaug,
sdk:ncs v1.2
Routine path:D:\ncs\v1.2.0\nrf\samples\nrf9160\at_client
The routine is attached:
The test results are shown in the figure below: ...
Hi,
I want to update the firmware of my Nordic controller nrf52810( DFU Target ) using ESP-WROOM32(DFU Controller) using BLE protocol.
Please suggest how to proceed. ...
I am trying to communicate between my mobile Bluetooth and a BLE sysyem (Bluetooth low energy chip and evaluation board). The BLE chip I am using is NINA-B301 and evaulation...
I experimented with nRF52840 for 1 month. It was uploaded to the board well before, but suddenly I can't get the port.
So after finding a lot of Q&A, 1. Press button-4 ...
I've just moved over to the latest SDK version 1.3.1 (i uninstalled the previous version before installing the new one)
I installed it via the toolchain manager as usual...
Running an application that is using a 32 Mhz SPIM3 interface and it is working fine on our custom board.
As part of the interface testing, a logic analyzer was used to...
According to what I know, the nRF52840 lacks hardware to support AoA as defined in BLE 5.1. Still, the web page of the device mentions that it supports BLE 5.1. What is the...
Hello, I'm trying to send some payload via ELECTRICAL_MEASUREMENT cluster. The sending is realized in the similar way to the zigbee_light_switch example. I'm sending data...
Hi,
We have been working with an end device based on nRF52840 with nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b
By measuring with the power profiler kit, we got a system...
I am developing an application that includes custom services. The application is updated by the bootloader. I looked up the post about NRF_ERROR_NO_MEM and modified sdk_config...
Hello, i have a question about program interaction with softdevice and using timeslot API.
I have custom board with nRF52811 chip on it and want to realize peripheral and...
Hello,
I have been playing around with LTE PSM and eDRX modes and had some questions regarding configuration.
If I configure the PSM/eDRX timing windows, how do I know...
