Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
Good day!
As base I used this examples:
ble_app_multiperipheral - for connection handling
ble_app_hids_keyboard - for whitelist and bonding
Error occurs after...
I am inquiring about the ability of the nRF9160, does the device have the resource to be a picocell? Specifically, can it handle communication to and from a single cell phone...
Hi
I‘m working with the SDK since many versions. One thing I don‘t understand is the sdk_config.h concept.
My first thought was that there is a master sdk_config.h in...
Hi, I made a PCB board nrf51822.
Because of my mistake, Rx, Tx pin was not cross connected to MCU.
So i want to change Rx <-> Tx pin.
In the example of ble_app_uart_s130_pca10028...
hi,everyone
when i test the mesh/example/dfu , it is upgrade scucessed,but when i combine it to switch_light example ,it was failed , it looks end the transfer too early...
Hi, there~
I'm trying to make my own bootloader and starting with the secure bootloader sample code.
The problem is the orignal bootloader, that is compiled with secure...
Hello,
Recently I started working on BLE. I need details with respect to BLE 5.0.
Below are the features of BLE 5.0
2x Range (With 2Mbps PHY)
4x Speed (With...
Hi,
I've created 3 PWM pulses via:
Which works when I'm not starting Thread (from the examples/thread/freertos_coap_server example)
But when I start Thread...
Dear Sir,
I am working on the following scenario.
I have BLE device ( SDK 15 and softdevice s132). It is advertising for specific duration.
There are different phones...
Hi,
I am working on a project where I am sending and receiving Encrypted string data from my phone with nRF Toolbox to the nRF52840 DK. The basic paring is established along...
I recently got past an issue with not connecting to the LTE network getting an nrf_cloud_connect failed: 60 and had things working yesterday. I had support for that issue...
Hey, I'm trying to connect a touchscreen monitor (10 finger) usb into a computer, get a raw input report and send it over uart to bluetooth module and sent it to other computer...
In IAR it shows the cycle count registers and they appear to work as expected in that view (shown as CYCLECOUNTER) . In the IAR Project/SFRSetup it shows the address of DWT_CYCCNT...
Hello,
I am developing a simple HID device with output report to receive data from PC. I took keyboard example as base project and I want to increase output report size...
Hello!
I have a custom nRF52832 board with an FTDI usb/serial part running my app successfully.
I generally program the board with a JLINK and SWD, but I am working to...
