The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hi,
for a project based on the nRF54L15, we are evaluating the new single-slot DFU mechanism.
Using NCS v3.2.1, I am testing the sample available at: https://github.com...
Based on the DevAcademy here is my following setup using a custom NRF54L15 chip with the NRF54L15-DK devicetree with following overlay:
prj.conf:
CONFIG_GPIO =y
...
I'm trying to configure the nRF cloud log backend to aid with debugging of devices during field tests without the need for bulky UART harnesses to capture logs from the serial...
Hi everyone,
We’re trying to use UART1 on the nRF9151 DK in non-secure mode , mapped to the Arduino R1 connector. However, it seems to be reserved by TF-M , and we cannot...
Hi,
I want to reduce the time required to read 16 KB of data from the datalogger. Currently, it takes about 6 seconds to read all the data. How can I decrease this time...
Dear Support-Team,
I have checked that now back and forth: When I add
CONFIG_NO_OPTIMIZATIONS=y CONFIG_MAIN_STACK_SIZE=8192 CONFIG_SYSTEM_WORKQUEUE_STACK_SIZE=8192
in...
So I have this nRF5340-DK board where the Segger programmer/debugging chip is the same size as the nRF5340 SoC. It recently broke when I was moving and I am about to purchase...
Hello,
I am trying to measure nRF9151 current using Power Profiler Kit II, running Cellular UDP project on EVK and following the steps in:
https://docs.nordicsemi.com...
Hello
I am using nRf52805 based BLE peripheral using the Nordic UART Service (NUS). The device transmits numeric data periodically using GATT notifications (NUS TX), and...
Hi,
We have products in the field using SDK 15.2 with its associated S140 SoftDevice s140_nrf52_6.1.0_softdevice, and bootloader.
We are upgrading our application to SDK...
I've succesfully setup multiple nRF7002DK boards with an example app to connect to WiFi.
One out of the five boards the Wifi does not work. The interface stays down in Zephyr...
Hello community
I have tested the v3.2.1\zephyr\samples\boards\nordic\system_off example and it works fine on my nrf54l15dk. Now i wanted to use parts of it for my custom...
Currently I learn the current DFU example from nrf_sdk but I failed in the last step:
I compiled the bootloader example secure_bootloader\pca10056_uart
in the...
Hello, when sending audio packets using a broadcast stream one can provide the seq_num of the packet (using the function `int bt_bap_stream_send(struct bt_bap_stream *stream...
Symptoms:
When running Bootloader + SoftDevice + App (with SoftDevice enabled in the app), The bootloader runs correctly and starts SD. The app is started, but crashes...
