Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
I am trying to interface nrf52833 devkit with BG95 devkit using PPP connection. For this I am using gsm_modem sample code. But when I am getting error while build configuration...
Hi,
We are wondering the current consumption in our custom board. The board has the following components (my FW view :)
nRF9160 - powered directly from batteries (either...
Hi
I use nRF7002-DK and sdk version as v2.5.2,download lesson8 exercise 3 solution and build was error as below log, which parts am I miss?
build config as below
...
Hello,
I a working on a project that uses the nRF5340 CCM peripheral (Network core) in an asynchronous mode. That is, I encrypt PDUs prior to scheduling them for transmission...
I want to configure my setup for secure boot and enable TFM and encrypted application images for firmware update. I am using nRF sdk version 2.5.0. My board is nRF9160. Now...
I have setup the UART along the same lines as the sample project in the DevZone Academy. I have extended the example provided to suit the project needs.
What I am getting...
Hi all, We have a custom board running with a project based with ncs v2.6.0. On our board we have two external flash, one is used for DFU the mcuboot_secondary with QSPI and...
Hello All,
I am not able to find the nrf_drv_adc related files in SDK folder. ADC library is not supported in NRF5_SDK_17.0.2 is it so?
Thanks and regards,
Neeraj...
Hi Team,
We are testing the nRF7000's Wi-Fi location feature to enhance our device's capabilities.
Our setup includes:
nRF52832 as a BLE beacon
nRF9160 as a host...
When I follow exercise steps A to open nRF connect terminal,vs code will display issue as follow:
Whether some issues happened when I get nrf connect SDK?
How can I...
Hi community,
It's my first time building a board with a Nordic chip so for sure I've made a lot of mistakes. I made this with KiCad and uploaded all the files to the repository...
What is the possible reason that LED1 blinks and LED2 does not light up when the nRF5340 Audio source is operating?
I have read and understood the source code, but I am...
We've added our app's overlay files into the mcuboot child_image directory so that mcuboot is initialized with the proper state of the board. In our nrf5340_cpuapp_common...
Hello,
Using wifi monitor sample on NRF7002 DK, packet length is constantly 70. It was checked both by reading received variable from:
received = recv ( packet -> recv_sock...
Hi Nordic DevZone Community,
I am working on a project using the Zephyr RTOS with an nRF52833 series board, and I am trying to interface with an SSD1306 OLED display via...
