Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
Hey
I am struggeling to build the smp_server sample for the nRF5340:
west build -p -b nrf5340dk/nrf5340/cpuapp/ns -- -DFILE_SUFFIX="nrf5340_bt"
fails with a linker error...
Hi Nordic Team,
I’m currently using two standard nRF5340 DKs (non-Audio DK) running the nrf5340_audio application.
We’ve successfully adapted I²S speaker output on unicast...
Hello, I am going to use nRF52833 to develop a remote controller based on Zigbee RF4CE specification.
From the nRF5 SDK for Thread and Zigbee, it looks like RF4CE should...
Hello,
Is there a way to change the LPCOMP reference level in Zephyr other than what is set in the devicetree overlay?
I'm happy to disable it, change it and re-enable...
I am experimenting with the Nordic ESL sample application. The central_esl app is running on a nRF5340DK. I would like to add the nRF21540EK to this to improve the range....
I'm suddenly getting this error message with nRF Connect for Desktop. I've tried deleting and reinstalling, but the same error persists.
What should I do?
Error: Failed...
I'm not able to debug any of example applications that uses non secure build. Non ns versions works fine. I have added CONFIG_TFM_CMAKE_BUILD_TYPE_RELWITHDEBINFO =y to my...
Hi everyone,
I'm trying to interface the nrf5340 with the intan chip rhd2132, that allows to record signals. I can read successfuly the registers, but when I try the recording...
Hello,
We are using nRF54LM20A and NCS3.1.1 for our current product development.
we were using PDK/DK for our development and we got the datasheet "nRF54LM20A_Preliminary_Datasheet_v0...
Hello everyone!
I'm trying to get a custom board based on the nRF54L10 working. I am currently connecting it to my computer via a J-Link Edu and would like to get some basic...
Hi Nordic Team,
I am using NCS v3.0.0 and working on a Matter-based application.
I have enabled the ActiveHardwareFaults attribute (0x0005) in the General Diagnostics...
How can I confirm that an nRF52840-based device has been successfully provisioned? I don’t have physical access to the device, and it is running firmware that performs self...
Is there a sample app that uses the Zephyr Light CTL Bluetooth Mesh model? I've tried to add that model to the light_ctrl sample app, but get a crash during configuration...
Hi,
Using nRF9160 - NCS 3.1.0
I am trying to implement the AT%XBANDLOCK at command into my Firmware, and I am struggling to set it with the nrf_modem_at_cmd() function...
Hi
in my application, I need to reduce /disable RAM sections in nRF54L15 to save Idle RAM current. For Example, I need to retain only 64KB RAM when I am in idle.
how can...
