the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I have 9 sensors based on NRF54L15 working as GATT server. I push around 100 bytes every 15ms from all sensors to the central hub. When i connect all nine of them...
Hi everyone!
I am developing device based on nrf25833 mcu which should transmit data to android devices using ble characteristic notification mechanism (data received...
Hi!
Recently I bought this device (v1.1.2) and I was very happy about it until I tried to verify the current and voltage readings. Tried two multimeters and they both agree...
I am porting and existing app to nRF Connect SDK 2.7.0 from 2.6.1. Using sysbuild, MCUBoot and the app are building and I am able to load the firmware onto the PCB and it...
Hello!
I've just come into contact with the nrf54l15. On the customer's board, it is necessary to change the NFC pin to a regular gpio, and they following the previous nrf52...
Hi Is it possible to configure project to use simultaneous multi image DFU and serial recovery over USB? I would like to be able to update both cores using dfu_multi_image_XXX...
I have an LED connected, and I want to use PWM, but enabling it adds about 700 µA of passive current — both when the output is high and low. However, if I set the duty cycle...
Hi,
I'm developing on the nrf5340 and the semtech LR1110. I'm using the latest SDK version 3.1.1.
I saw in the SDK that there's a library for the LR1110, but I can't activate...
Hi.
I try to build the example Matter: light bulb and in the terminal shows an error that iI don´t underestand what is the problem.
Please ¿Any could explain me why ocurs...
Hi,
I am using the Thingy:91X device and can see the updates appearing on the hello.nrfcloud.com web application, but I would like to have access to the 'device' via the...
As the title said, I'm currently on the nRF21540 DK. I turned on Async UART:
CONFIG_UART_1_INTERRUPT_DRIVEN =n
CONFIG_UART_1_ASYNC =y
CONFIG_UART_1_NRF_HW_ASYNC =y...
Hey Nordic Team
Just looking for guidance and clarification on the nPM1300 setup. couple of questions on the sample setup below.
Project Overview
Project is a consumer...
I setup 2 Holyiot nRF54L DK Development Boards with the channel sounding sample code from NCS 3.1.1 samples/bluetooth/channel_sounding_ras_initiator (initiator and reflector...
We have designed a custom board around nRF54H20 EngC revision and testing it on NCS 3.1.1. We were able to do provisioning and bring up using iron-side binaries. But got two...
