Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi,
We are working on power optimization for our project using the nRF5340 board. Our code implements an RTOS, BLE for data transfer, I2C and SPI for device communication...
Hi,
we are developing a solution where the number of peripheral BLE devices is increasing and we need to manage up to 30 realiable connections. We have been working with...
Hi everyone,
I'm trying to send updated gyro and acceleration values from MPU6050 continuously by BLE function from nrf52832. I'm currently using the nrf52 development kit...
I would like to inquire whether there is a sample or guide to search for and connect to iPhone background advertising when operating with nRF52840/5340 Central.
https...
Hi
Followup on this ticket: Enabling SPI and TWI drivers on Zephyr
First the fundamentals, I am using:
nRF52840-DK
nRF Connect for VS Code: v2024.7.13
nRF...
Hi
First the fundamentals, I am using:
nRF52840-DK
nRF Connect for VS Code: v2024.7.13
I am trying to create a demonstration project, where I need both SPI and...
Hello, I.m using SDK 2.6.1 with VSCode.
I created a new application based on the sample /nrf/samples/net/mqtt configured for nRF9161_ns which is listed as a compatible board...
I have three nrf5340 board. Now i want to use one as bis-headset and two as bis-gateway. I want to get two audio from two bis-gateway at the same time. Can i do it? How ?...
I am using an IMU sensor in sensor hub mode (LSM6DSV16X, LIS2MDL) with the FIFO interrupt interval set at 30 Hz. The data is sent over BLE. It works perfectly when using RTT...
With nRF7002DK and TF-M (nrf7002dk_nrf5340_cpuapp_ns.conf) configuration, the sample project works for example.com:
*** Booting nRF Connect SDK v3.5.99-ncs1-1 *** HTTPS...
During my test of the nrf5340 audio application which in the V2.6.0 SDK , Because of that i need to implement some algorithms in it, i use the ld file to allocated a segment...
I am having trouble understanding how to measure the power consumption of the nRF9161DK as recommended by the documentation: https://docs.nordicsemi.com/bundle/ug_nrf9161_dk...
I'm working on a complex legacy codebase for the nRF52840, which uses nRF5 SDK 15.0.0 and the S140 SoftDevice v6.0.0. The device previously only used a custom RF protocol...
Hi,
I'm using SDK 2.1.0 for this project.
I found that when I shut down using the following:
pm_state_force ( 0u , &( struct pm_state_info){PM_STATE_SOFT_OFF, 0 ,...
Hello,
I’m trying to get an nRF21540 FEM working with a chip-down nRF5340 design under NCS v2.4.2. I’m able to enable the FEM at its default gain setting, but I hit a wall...