Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hello, guys！
I'm currently just starting to work on the nrf9160dk board. I want to try to explore the communication of nrf9160 with external acceleration sensor. First,...
Hi Team,
Is there any blog/tutorial on how to add custom profile (service/characteristics) with ncsv.1.8.0 and nrf52832/33?
I could find a couple of blogs but they were...
Hello everyone, I'm testing the example ble peripheral "UART/Serial Port Emulation over BLE" with SoftDevice S112 nRF5 SDK v17.1.0 . My board is MBN52832DK and i'm using the...
Hi,
in my project I use the nRF52840 microcontroller as the master I2C device.
Sometimes the TWI peripheral SDA line is forced to a low value by the slave device. This...
Hi, I'm developing an application using fds. I merged fds into ble_app_uart and built complete But when program run fds_init() nRF was crashed I called fds_registered before...
I am using NCS 1.7.0 and latest nRF5340 DK
I am trying to update netcore firmware using the process defined here: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1...
Hi everyone!
I have a question regarding the audio support on the nRF52833 chip. Is there any support for sending audio ( Low quality compressed audio ) to headset? Or...
Hi everybody.
For a personal project, I need to integrate a flash or a microSD card to store data.
As computation core I want to use nRF52811, but I'm not able to find...
Hi,
I've lost hours to this so grateful for your support!
I have a custom board using Raytac MDBT42Q, which has a 32MHz clock in the module and I'm not using an external...
To whom it ma concern,
we observed Unkwon Resets after Long runtime ; Several Hours.
We use the NRF52840.
After the reset bit 1 in RESETREAS is detected .
BUT investigation...
My project is based on 'ble_app_uart' and I added dfu service..
so there's two custom 128bit uuid in my project..
But before this, I only want to test dfu service mode...
Hi,
We have made an app that gathers GPS coordinates using an external antenna with the thingy91. The problem we have is that we struggle to test the code when we don't...
Hello,
I am using the nRF52840 dongle with the nrf sniffer 4.1 firmware running on it, using Wireshark to read out its results.
This works fine for advertisement packets...
Hi!
In my application, I am receiving A-GPS data from nRF Cloud. After the data is received there is a considerable amount of time where the GNSS module is blocked because...
