Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
When I was adding the ID of the sensor, I found that the specific name displayed on the Bluetooth app is not my own name. Is there a special definition for this ID? I checked...
Hi
I'm looking for a clear statement about to do or not do modem firmware downgrades on production devices.
I know that
nrfxlib does not mention anything about modem...
Hey, I'm working on a real-time body motion capture project and using nRF52832 as BLE MCU. In the system I have 3 IMU sensors to transmit sensor data to an Android device...
Hi,
This is a repeat of case 279137 but I see no answer to that so here goes again...
I am building sample Zephyr applications in VS Code. Everything was working fine...
Hi!
We would like to be able to send two separate dfu-packages independently, one hex/pack containing our main application and one hex/pack containing data to be read by...
HI All,
We are using NRF52832 for our project.
1) We are using System ON mode to put NRF52832 in to sleep mode. We are able to put NRF52832 in to sleep mode(System ON...
Hi,
I am working with the nRF52832 DK. I want to program a couple of ICs with SPI every 2 ms. I have successfully configured the nRF as SPI master and I start the SPI transfers...
Hi All,
I wanted to look at the power profile for my nRF52840 dongle, I installed nRF connect and installed the Power Profiler. But as I want to the option to connect the...
Hi，
Hello everyone, I have encountered a problem in the pairing and bonding process of BLE.I use two NRF52832 development boards, one acts as a slave and the other acts...
We use FreeRTOS with nRF SDK driver library. The driver library is working well because it doesn't dynamically allocate any memory. So I can simple take entire memory block...
I'm facing some problems when trying to run my custom board on standard batteries.
The device boots fine but when the LTE modem connects I get a reset.
The nrf9160 is...
Target nRF52832(nrf52dk_nrf52832) SDK NCS v1.9.1
I need high performance data transfer, so I review throughput sample. C:\Users\user\ncs\v1.9.1\nrf\samples\bluetooth\throughput...
We are using nRF9160 (Development Kit), SDK 1.9.1 board with "serial lte modem" firmware. We are trying to get AGPS coordinates (using an external antenna), but for some reason...
In the nrf5340 development process.I compile an app core hex from project A and a net core hex firmware from another project B. what method can I quickly obtain a merged firmware...
Hi,
I'm trying to get the maximum possible throughput from a peripheral device, sending notifications to a central. I compare the throughput between 2 PCA10040 boards...
