I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hi,
I'm writing a decoder for a custom radio protocol and I need to measure the rising and falling edges of a signal with high precision. I'm currently using the COMP peripheral...
Have been trying for hours, and searched through the forums, but no luck yet. Modem firmware doesnt seem to load with the following setup. Downgrading to previous Programmer...
Hello,
NCS1.8.0 Windows10 X64,
periodic_adv had set BT_LE_ADV_OPT_CODED and BT_GAP_ADV_FAST_INT_MIN_2 /* 100 ms */
periodic_sync scan info "Prim: LE 1M, Secn: LE Coded...
Dear Sir,
I got error like '[00:01:44.604,858] <error> app: ERROR 1813 [Unknown error code] at KGJ`hó@h:536871936 PC at: 0x0001505C' and I can't where did it happen, I...
Is SD340 v7.0.1 compatible with nRF SDK 17.1.0? https://www.thisisant.com/developer/components/nrf52832/#tab_protocol_stacks_tab
Reason I ask is on the InfoCenter there...
Hi all,
I'm working on the nrf5340 with a modified mesh light sample and nrf connect sdk 1.7.1
I'm measuring from P0.28 which is also LED1 to the GND.
After programming...
Hello,
I am using nRF5 SDK for Thread v4.1 for thread implementation using nRF52840 SOC. I have used mqtt-sn sleepy publisher as my base example to develop my software....
Hello,
I am struggling trying to make this sample work on my board. I changed my prj.conf file with these lines:
And looking at other questions I discovered that sometimes...
Hi,
Is there any way to make app_usbd_audio_class_rx_start(...) complete the data transfer within the same context, rather than defer to user event
APP_USBD_AUDIO_USER_EVT_RX_DONE...
We have been using nrf connect installers 3.3.0 and now 3.7.0. We have recently seen issues with new users encountering this error when installing 3.7.0. Are there any solutions...
Hi,
I started to evaluate the Instaburst feature. I use light_switch_client example, but I am unable to provision the device once I enable this feature.
Below are the...
We are in the early phase of architecting a product that uses BLE and a proprietary RF protocol using the nRF52840 and are considering the addition of the nRF21540. In sifting...
I am currently trying to create a simple BLE observer which listens to advertisement broadcasts from a specific device (given via address). I attached the source code below...
Hi,
SDK - 17.1.0
I want to store my sensor data to the internal flash memory of nRF52810 for a long time. I have some questions here:
The data sheet says the flash...
Hello,
Few years ago I developed an application for nRF52832 (BMD-300). Now our customer wants to port the application to nRF52810 (BMD-330) as BMD-300 is not available...
