I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
I would like to know the natural interrupt priority among different peripherals of nrf52840.
Specifically I am looking for default interrupt priority between RTC1 and TIMER1...
Hello, guys. I'm using the PCA10040 and the SDK 16.0's BLE UART peripheral example. I am trying to make PWM signal below.
When PWM0 stops, PWM2 works, and when PWM2 stops...
Hello everyone,
I am working on an nRF52-DK and getting familiar with Zephyr. In this process I am currently trying to extend the BLE MTU size beyond the default 23 bytes...
Hello,
My device is a USB HID peripheral connected to a PC. There is a case when the PC is turned off, but USB power is present. I want to detect this situation.
At the...
Is it possible to detect the presence of a Low Frequency Crystal and configure softdevice to use if present, otherwise use the internal RC oscillator?
A proposal would be...
Hi,
we have troubles to use 4wire NRF LPUART between nRF52840 (client) and nRF9160 Serial LTE Modem app (server).
We use v1.5.1 of nRF Connect SDK.
For nRF9160 we added...
Hello Team,
I want to know while Ble device is connected to the android device and within 5mins if device not get any data from android device then,
- Can device enter...
I am using sdk for mesh v.5 (s140.7.2.0) and nrf52840 DK and want to add uart peripheral into the client in the light switch mesh example and then trigger button 1 once a...
Hi,
I have written Hitachi AC IR transmitter using Smart remote 3 library.
Smart remote 3 library support 2 AC protocols, i.e., SIRC and NEC.
Kindly guide me how...
Hello, I essentially want to figure out a way to use the NFC buffer received by code like the writable_ndef_message example and have that same buffer, in the same code, advertise...
Hi
the new nRF9160 Modem FW 1.3 supports Non Ip Data Delivery (NIDD) on NB-IoT In nRF Connect SDK, there is a new example that can be used to test some modem functionalities...
develop tool is nrf5340dk and sample peripheral_uart in NCS1.5.0 ,when debugging , function uart_cb() alway run in case UART_RX_DISABLED and case UART_RX_BUF_RELEASED
,code...
Hello,
I am developing a product using nRF52840 and BLE communication of my product uses NUS.
SD: s140_nRF52_v7.0.1
SDK: nRF5_v16.0.0
Recently, I want to encrypt...
