Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hello, I am using the nRF52832DK with the peripheral_nfc_pairing example. With nRF Connect Mobile the NFC OOB pairing works fine, but when I try the same with my own Kotlin...
Hi
I've recently tried to move from SDK version 2.6.3 to 2.9.1. However i've run into issues with this transistion.
I made a new custom board, by following the guide...
Board: nRF5340-DK SDK: nrf ncs v3.0.2 Hi, On the project I am working on there is a tight timing constraint for DMA timeout (30-40us). Also there was a need for specific baudrate...
The current default and only recommended way to use MCUboot is to make the private key available as part of the build process.
There have been several questions about this...
Hi
we are using nrfx drivers for nRF5340 with gcc-arm-none-eabi and they work great. Now we are planning to move to another compiler and I have a couple of questions:
...
Hi, This is my basic information:
CHIP: NRF52840DK
SDK: NCS2.9.0
Project: Matter Bulb
This is my question:
I want to commission bulb into 2 fabrics, but when I...
VS Code is not loading for me today:
I followed this thread but it seems like permissions are fine...I think. Here are the errors in the log:
Activating extension...
Hi all,
I have an issue with achieving bigger sizes of ext adv data as 31 bytes.
My current BLE code is pretty much the same as the nrf_dm sample code:
https://github...
I have a custom board, with nrf5340, nrf7002 on it.
I would like to get the uA levels of power consumption I see other nrf5340 projects talk about (eg here ) when my application...
Is there any characterization for the nPM1304 (or any in the series) with a charging input voltage in the 3.5-4.0 range? I have a ~4V power source, but depending on load it...
Hi,
I'm developing a project that requires to write GPS data to an SD card. I'm using Nordic SD card library.
I'm able to initialize and interact with the SD card only...
Hi there,
I am trying to send large data files via BLE notifications. My setup is nRF5340 development kit sending data to connecting devices (phone, PC).
I have gone through...
System description
I have an nrF54L15 mounted with an external 4 Mbit External flash with FATFS configured
Filesytem config:
# FatFS File system
CONFIG_FILE_SYSTEM...
Hi
About nPM1300
We will use load switch to drive haptic function and its peak current may up to 0.4A~0.5A@25us duration,
I see the spec show the load switch with maximum...
