The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I am using nrf52832, and I want to use SYSTEM ON Sleep. Also , my wake up sourses are timer based, and also GPIO interrupt based. But I observed that the device cannot go...
Hey there!
I am currently in the process of trying to setup a simple ISR routine triggered via GPIOTE.
However, when calling nrfx_gpiote_init() or nrfx_gpiote_input_configure...
Hi together!
In my current project I would like to send some sensor data to an Azure IoT Hub, by using a nRF52840.
In the first step and for evaluation I used a nRF9151...
Problem: We have a huge variability in received RSSI (see picture) despite both devices being stationary in test setup. For our use case, accurate RSSI is critical. nRF52840...
Hello DevZone
I am currently facing an issues with device already installed at my customer. Devices are based on nRF9160, firmware based on SDK 2.8.0 and modem 1.3.6. Once...
Hi, Background For some time now I have been troubled by a bug in one of our products acting as a BLE central device. The bug manifests itself as the central reporting that...
I see that the nRF5340 is certified PSA level 2 whereas the newer nRF54L15 is certified level 1.
You claim the nRF54L15 is " designed to meet PSA Certified Level 3 ". I...
Hello Nordic support
I have encountered what I think is a bug in ICMSG. The attached sample shows the following behavior:
The first time it runs, the app and flpr CPUs...
Hello Team,
I am not able to flash any firmware to nRF5340 which is available in Thing 91x. I had tried peripheral_lbs example which was working fine. When I tried to...
Hey everyone,
I’ve been banging my head against an issue with my custom nRF54L15 board , and I’m under a bit of pressure to get five samples working. Unfortunately, the...
We are operating the 32.768 kHz low-frequency clock of the nRF52805 using the internal RC oscillator (LFRC).
We measured the LFCLK frequency of 100 devices, and the observed...
Hello, I'm trying to use the nRF54LM20A, but I'm a bit confused about the reference circuitry. What does "VDD_USB_3V3" refer to? What about all the different antenna labels...
Hello Team,
I am working with nRF52833 configured as a BLE scanner using nRF Connect SDK for VS Code .
Here is my prj.conf:
AND here is scan/conn Implementaion:
...
