Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi Networks,
I have tried to build the nRF5340 DK as a gateway.
Enabled
1. CONFIG_BT_GATEWAY=y
2. CONFIG_BT_GATEWAY_ADV=y
3. CONFIG_BT_GATEWAY_GATT=y
But not acting...
Hello,
I will be designing a board using with nRF52833 with the NRF21540 for the added gain. Would it be possible to add adaptive frequency hopping?
Thank you,
Shah...
The central device has the below settings
One central device A and two peripheral devices B and C, B and C have the exact same firmware. A can establish the connection...
Hello
I have implemented the stereo function to the nrf5340 audio application on SDK V2.6.0. i can send stereo audio signal to both of the two headset at the same time or...
Hi, I recently got nRF5340 Audio DK for my work. I have been try to use the onboard mic for collecting audio and transmit it via BLE, since I'm a newbie I couldn't do it....
Hi
I have successfully added the nrf_crypto files to the UART project. It compiles without any issue. Now I was trying to run the ECDSA example code in the UART project...
I used nrf52840 board with SDK 17_1_0
I used segger embedded studio IDE
i want to Implement two VL53L5CX TOF sensor with nrf52840 so i used two TWI,
but when i init...
Hello,
I'm migrating my project from using child/parent to sysbuild ( simple Hello world code, and using MCUBOOT + NSIB ).
The first error i faced when moving to use sysbuild...
Using Zephyr.
I'm looking for a process or a function to log unconditional message in the logging system including timestamp and other typical logging/display functionality...
We have a custom board with an nRF9160 directly connected to a SIM-S-IO3-MFF2-2 IC. I understand these kinds of eSIMs in IOT devices are typically provisioned over-the-air...
I have a slightly off the wall requirement where I need to send a serial data stream at 5kbps, it will be used to drive an external OOK 433MHz transmitter. The data format...
Hi,
I am having some issues when trying to enable the Fast Pair when executing the bt_fast_pair_enable(). I used the debugger to determine where it's failing:
...
Hello,
I am working on setting up the nrf52 (nrf52832) to communicated with the AD4130 from Analog Devices via the SPI Port. However, I am encountering a problem that I...
Hi,
I'm using the nrf9160, sdk 2.4.0 and tool chain 2.6.1. I need to scan the i2c sensor, I didn't find the i2c scanner example. So i was add one code and tested i'm getting...
I am trying to test the light switch and light bulb example with google home app and google nest device as a border router. I have flashed the bulb example into a nrf52840dk...
