I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
I got the Dynastream N5 kit and have successfully used it with limited ANT work and was trying to get BLE working but can't get a driver for the USB dongle. On the 51422 product...
Hi All,
I am working in the sleep mode with system off and wake up with internal RC clock.
It function well when connected to EV board...
I see the "Emulated System...
Hi,
I'm use ncs sdk what to send ADV_EXT_PDU Advertising, but this PDU every time send 8 advertising event, however, i'm notice that ncs sdk only use 8 second advertising...
I have a product under development that needs to send USB key codes to the PC that are outside the range that is supported by the USBD library and I am wondering the best...
Hi,
I´m developing a BLE-OTA driver for a BLE SoC and I try to use the nRF52840 dongle with my PC as the second device for the OTA mechanism by using Python and the pc_ble_driver...
I'm trying to create a HAL library to use it with zephyr application
From what I have read I need to create another module .
I can't figure out how to set up the module...
I am using the nRF52840-dk with the nRF Connect SDK v2.0.0 and for the development itself I use Visual Studio Code.
My Goal: Both the bootloader and the actual application...
Hi,
In my project, I have finished the application core code.Then I need to debug net core, but when I selected the "hci_rpmsg" target,and click the debug button.The debugger...
Hello my question is I am giving supply with lithium 18650 battery whic voltage is 3.7 to 4.2 volt but the battery falls very much below .
My question is when using HIGH...
Hello,
I'm working with NUS service and the nRF Toolbox app. I need to send multiple messages from mobile app to DK. How can I do that?. Is there a macro/script example...
I'm currently evaluating the nRF52840dk using the nRF Connect SDK to determine whether or not to port over our codebase to it from a Xiao nRF52 module I was using KVStore...
Hi,
I am trying to flash nrf52840 dk board with open thread binaries.
I see that, sporadically the device gets readback protection enabled.
I use the following command...
Hi
I have two PCA10121 and followed the instructions here to get the demo audio application to work.
The output of:
python3 buildprog.py -c app -b debug -d both
is...
I am writing my own code (no libraries etc.) on nRF52832.
For new i still have softdevice and bootloader in flash, and store my program using bootloader protocol, but my...
Hi There!
I'm using the dimmable light bulb example and have extended it with the color control attribute list. I'm using the zb_zcl_color_control_attrs_ext_t in combination...
Hi, I am working with custom board in that, trying to read NTC sensor value using 2 (NTC+ and NTC-) ADC pins. Applied Steinhart formula to convert temperature. In that, After...
We have a product that uses an nrf52832 module (vendor listed on the 3rd part modules list) and have shipped ~30,000 units using the current circuit design. We are using SDK...
