Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hello, I am having a problem with the development on a custon board. During system-off I wake up the chip with nrf_gpio_cfg_sense_input function on PIN 5. The chip wakes up...
Hi
I am designing a new BLE device and have some questions about the PCB antenna.
The product will be worn on the body.
I have a 4 Layer PCB with 1.0mm with and 35u...
Im trying to use the BLE LTE Gateway running on a NRF9160DK
I have the NRF52840 running the lpuart_hci code and that is working fine i can configure the BLE from the NRF9160...
I have nRF9160DK kit. The iBASIS SIM does not work in India. I aaranged a M2M SIM from Voadfone. The Vodafone SIM has 20 digit ICCID printed on it, while the nrfcloud accepts...
SDK version - 15.3
Segger version - 5.42
DK - nRF52840
I'm a beginner and I was following this tutorial our_services . The code given in the tutorial worked for SDK...
Hi
I am testing nRF52833 UART DFU function, but there is an error in merged HEX file,
Parsing input files. Merging file "SD.hex" into output. Merging file "APP.hex"...
When associating a pin with the UART, is it possible to still configure the pin to be open drain and with a pullup, or does the peripheral associating override those sett...
Hi :) ,
I'm using TWI to connect a sensor that i supply with an LDO regulator.
This LDO has an enable pin controlled by P0_23. Driving current is max 1uA so i configured...
In our project, we have defined 5 FDS_VIRTUAL_PAGES each of size 1024 words and have programmed to do GC if > 10 records are deleted. I see the 1st page being used for storing...
i have installed segger ide and nrf connect for desktop for programm nrf9160 , i have successfully uploaded Blinky code (zephyr) .but now i want to create a new project ....
Hi, I am trying the MQTT_SIMPLE sample on both the nRF9160DK and my own custom board. I have mfw_nrf9160_1.3.1 on both nRF9160 and I am using SDK v1.8.0. LTE connection seems...
Hi,
I'm using NCS 1.8.0 on a nrf52840.
I've got what seems to be a corrupted external flash Settings file. The issue doesn't seem reproducible yet, but as it happened...
I am working with SPI for the mfrc522 RFID reader. We were able to read the card previously while we used nRF connect SDK version 1.5.1 and nRF connect 3.6.1
Now I am not...
I'm using modem version mfw_nrf9160_1.3.1
It's waiting for semaphore and when CSCON notification came in between it's just resetting due to some hard fault. Can somebody...
Hi there,
I have gotten to the very last step of the following tutorial: https://www.youtube.com/watch?v=kdMJQFDRoss
The issue I am facing is that when pairing the Matter...
