Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
I have two beacons which are UUID filtered successfully.
I am trying to fetch major but this cannot be done just by putting an offset to p_adv_report->data.p_data. I noticed...
Hi,
nrf52 using from ble-peripheral-> ble_app_uart examle
In that ble_app_uart example receive the data from the android is ok.
But,i want transmit array type of data...
Hi.
setup is 52832, S332, SDK 15.3.0.
issue is about reset voltage.
I use CR2032 for power supply.
repeat fast put on and put off CR2032 on custom board, sometimes...
Hi All,
I am using nRF52382 and sdk 15.0. I have two SPI devices using separate pins. They work just fine separately, when I try to enable two instances I get compilation...
Hi,
As mentioned in "nRF52840 Product Specification v1.0", I have setup the high voltage mode, and use VDD as an external power of 3.3V by setting NRF_UICR -> REGOUT0 to...
I want to use 52811 as central deice, which SDK and SoftDevice should I use?
https://www.nordicsemi.com/Software-and-tools/Software/S140
It says: SoftDevice S140 is a...
Hi,
I’m looking to build the Bluetooth HCI-RPMsg sample for nRF52811.
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/zephyr/samples/bluetooth/hci_rpmsg/README...
Hi,
If the app keeps sending data at a certain rate, the numbers will skip and the software will stop.
I tried to see how much data I could communicate and at what speed...
Hello,
Development to blink LED only on Nordic Thingy 52 has been started after referring the following one of the post from Nordic Devzone. https://devzone.nordicsemi.com...
Hi,
I am using nRF52840 DK with ble_app_ots sdk example. When flash the ble_app_ots to my nordic board and I am trying to connect the board with my mobille. Unfortunately...
nRF9160 GPS IGPS_CONTINUOUS_PSM - can you please explain the basic functionality when the GPS runs in power save mode (to reach 9,8 mA). I cannot find information in the data...
DK: v0.9.0 nrf: v1.2.0 supl fw: v0.5.2 modem fw: v1.2.0 OS: Windows10
I'm trying to use assited GPS in "gps" sample program, but it doesn't work. This is log. There is no...
Dear Nordic,
We are developing the Cat M1 module base on the nRF9160 V1.2.0.
When we try to evaluate the current consumption in eDRX mode, we found our module even unable...
