Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
I am trying to do an OTA update of the firmware on my device. I am using Nrf Connect SDK 2.1. I followed some of the tutorials and setup the device to advertise the SMP UUID...
I am using the VSCode extension (2024.12.55), nRF Connect SDK ( 2.9.0). I created a new project from the USB loopback sample to investigate how to configure a project for...
Hi,
I suddenly started getting MPSL ASSERT: 112, 2134 upon BT enable and upon research came across this post ( link ) and used following code:
HFXO starts on peripheral_lbs...
Hi,
We are developing a new project using the nRF52832 as our controller and nRF5 SDK 17.0.2 as our SDK.
We have integrated the NUS client and NUS peripheral parts from...
I have an application where I use the bt_gatt_write() method and I would like to obtain information about the number of packets sent in my operations.
I would like to know...
Hi,
I am baffled by the QOS handling (and/or not handling) in asset_tracker_v2, especially in view of the fact that there is a QOS library as part of the nrf repository...
Using the nRF Connect Desktop application and the nRF Connect SDK for my nRF9160dk.
I would like to monitor RAM usage during runtime of my program. In particular I am interested...
Hello,
I am trying to migrate a project nRF Connect SDK v2.6.2 to v2.7.0 for the nrf5340dk target board, particularly to update to the new hw model v2 and sysbuild. I am...
Hello,
I am using nRf21540 and nRF5340 in GPIO+SPI config, where SPI is controlled via MPSL and separate spi0 bus.
I have configured the board files based on nordic,nrf21540...
devicetree overlay file
// * Connecting ADC channels
// For more help, browse the DeviceTree documentation at docs.zephyrproject.org/.../index.html
// You can also...
I just ported your AWS IoT for MQTT from this repository .
If I keep IPv6 enabled, I can get the address information without any problem. However, if I disable IPv6, the...
I have a project that runs fine when CONFIG_BOOTLOADER_MCUBOOT is disabled, but when I enable it pins 15 and 16 are pulled high. I need the mcu bootloader to run but is there...
Hi All ,
Setup Used
nRF Connect SDK v2.7
VsCode
Ubuntu 20.04
Google Nest Hub2
Android 12 Smartphone + Google Home App
nRF 5340 DK
Endpoint-0 ---------...
Hello Developers,
I am k.hemasundar and i am working on the nRF52833 QAAA0 micro controller with segger embedded studio IDE. I have used nRF SDK of version 17.1.0 and 16...
