Hi, I have followed the instructions in Securely generating credentials for nRF91 Series devices - nRF Cloud but cannot connect to nRF Cloud.
I think the instructions on...
Hello,
I am writing to seek advice on whether there could be any issues if the DFU Service is always available.
Currently, the devices we are selling allow the DFU Service...
Hi,
I have multiple sensors (SEDs) and one or more Hosts (FTDs) in our application. Based on the distance or other similar issues, there is a possibility that a sensor may...
Hello,
Currently using a custom board that has the nRF52810 onboard along side an ESP32. I am wanting to update the firmware for the nrf chip from the ESP32 over UART. The...
I have not used Segger Embedded Studio before.
I loaded the "ble_app_pwr_profiling", and clicked on "Build and Run".
This is what the output shows:
Building ‘ble_app_pwr_profiling_pca10056_s140...
We have unit testing working with the Zephyr Unity/CMock setup, however the test runner (test_runner_generate) ignores preprocessor directives (#ifdef) and removes them when...
I'm working on a project that requires a touchscreen display (in a ~20cm screen size, diagonal), controlled by an nRF5340. I honestly don't know much about displays and their...
Hi, I have followed the instructions in Securely generating credentials for nRF91 Series devices - nRF Cloud but cannot connect to nRF Cloud.
I think the instructions on...
Hello,
I am using an nRF5340dk to create a PPI Timer as shown in the following code block: This code behaves as expected when the clock divider is 1 or 2 (my PIN toggles...
My project is using NCS 2.6.0, builds the _ns variant with TF-M and mcuboot, and targets nRF5340 with an 8MB QSPI flash (it's a custom board, but mirrors the 5340DK in this...
Hello,
I am writing to seek advice on whether there could be any issues if the DFU Service is always available.
Currently, the devices we are selling allow the DFU Service...
Hi,
I have multiple sensors (SEDs) and one or more Hosts (FTDs) in our application. Based on the distance or other similar issues, there is a possibility that a sensor may...
Purchased nRF52840 DK. Plugged it with USB cable to my Win11 PC Trying to follow instructions in the enclosed brochure, which points to nordicsemi.com/start52840dk Step 4...
Hi
I need to send data from nRF7002 to external CPU(STM32) use UART protocol, for HW nRF7002 P0.20 connect STM32 RX and RF7002 P0.22 connect STM32 TX, I try to use exercise...
I am trying to get the nRF Connect (Zephyr) fs_sample working with nRF5340 preview DK, but am getting the following errors: *** Booting nRF Connect SDK d96769faceca *** [00...
Hello. I am changing the firmware developed using 52832 to use for 52833. The initial change has been completed, and most operations operate normally. However, a problem occurs...
Hi guys, my setup:
- nRf Connect 2.6.0
- VS Code 1.88.1
- Apple Macbook M3 Max (ARM64 CPU)
- nRF52840-DK
I created a new project based on the zephyr button sample...
Hello,
I am trying to run the asset tracker v2.
I have completed the setup steps and configuration.
Can you please let me know what to do ?
I have read that the -128...
Hi, I'm currently trying to enable softAP mode and have an HTTP server set up at the same time with the nRF7002DK.
The programs/samples I'm using for each are: HTTP server...
I am using the Android nrf connect app to connect to NRF5340-DK after mesh provisioning.
android pixel 7
nrf connect 4.28.0
If Android nrf connect uses 'auto connect...