I am using nRF Connect SDK 3.4.1 on three nRF54L15 devices:
A ───────── B ───────── C
A–B: A central / CS initiator
B peripheral / CS reflector
B–C: B central / CS initiator...
Hi,
I have been using NRF PPK2 for two months,
today when the device was connected to docking station and only ground to DUT I notised " High current surge in the USB...
Hello,
I cannot download many of the applications offered in the desktop. I am trying to use the evaluation board for the nRF54L15 offered by ezurio (BL54Lu) and cannot...
Hi,
Is there a way to implement overvoltage lockout by sensing VDD using the ADC? Our goal is to claim that we have power regulation so that we can get full modular certification...
Setup
- Programmer: nRF54LM20 DK (PCA10184), debug out header P13 to an external board over a 10-pin ribbon under 10 cm, SWD0_SELECT grounded on the target side. The DK...
I created software and flashed successfully to the nRF54L15-DK. It is to toggle an LED on and off on P2.09.
#include <zephyr/kernel.h>
#include <hal/nrf_gpio.h>
...
I'm trying to establish a data connection from a Linux host through the USB network interface of an nRF93M1-DK.
The modem registers successfully on the cellular network...
Hello,
I'm developing a firmware based on Zigbee CLI sample and enabled DFU of app core and net core via serial.
Now I am setting a custom key for image signing and...
Hi, i've been trying to use gnss function indoors and therefore i need to install an external antenna on my nrf9160dk.
I've read the requirements but i'd like some professional...
i need information on power consumption during advertising and connection in my case its taking too much high current around 1 ma in advertising and 1.5 ma during connection...
I want to implement Buttonless DFU for nrf52833 but unable to get how to implement it. I have gone through some links but that seems to be unclear. How can I implement the...
Hello guys,
I tried to design a pcb antenna for a nrf24l01+, since my company doesnt allow to buy cheap smd breakout board version from china anymore
The pcb stats of...
Hi,
Is there any way to run calibration of the LFCLK at the same time as the RTC is running on the same clock?
At program startup I start the HFCLK, then run this routine...
Hello, I’m developing application for nRF9160 with Zephyr RTOS. Currently I want to add a task watchdog module with a hardware watchdog fallback. I use three threads which...
We created the transceiver side and receiver side sources by reusing the nRF5340 Audio source.
I am creating it in CIS mode using VSCode.
The build ends on the receiver...
Hello,
I am working on a project were two MCU's need to communicate with each other via UART. I am using async UART. I am stuck with this problem where after
PM_DEVICE_ACTION_RESUME...
I'm currently working on a firmware for a device where the app core and net core need to share some sensor and configuration data. I want to use the rpmsg_service for that...
Hi Nordic Community,
I'm currently working on FCC certification for a project and need to enable BLE Direct Test Mode (DTM). I'm using the `hci_uart` sample and have activated...
Hi,
I have design my own board using a µC to talk to the nrf9160 in at command. My code is working with the devboard, but I don't understand how to flash the AT command...
Hi,
I am using nRF52832 board with the SDK version nRF5_SDK_15.3.0 and soft device S132.
I have implemented the POF(power fail comparator) to generate event when the event...
I've got a project that I'm going to want to do DFU through the UART, and in order to transfer files in a follow-on activity, I want SMP running in the application. Therefore...
