Hi there,
My nRF5340 application requires the use of SD card with DMA and BLE transmission. Howerver, as soon as I turn on the device, I get the following errors:
A...
I'm using NCS SDK v3.0.2 and trying to build the Matter Thermostat example for the target: ` nrf54L15DK/nrf54L15/cpuapp/ns ` However, the build fails with the following errors...
when I try to build a code for integrating sensor in nRF 5340 dk, this error comes, I tried even after installing cmake manually from the cmake website https://cmake.org/...
Hello,
I am using an nRF9160 to connect to a private network. My nRF9160 successfully attaches to this network.
However, when reviewing the logs from the private network...
Hello,
How can I put the nRF54L15 into continuous wave mode? And I assume after entering CW that I can freely change channels using the FREQUENCY register (0x708). Is that...
Hi, I'm currently trying to add an Actinius Icarus IoT board as LTE device at nRF cloud.
I already know my board IMEI (I got it by flashing the AT client sample and then...
Connecting nrf21540 to a nrf52840. 840 GPIO default state is input, input buffer connected. One of the 840 GPIO pins is connected to the 540 PDN pin.
1) If the 840 gets...
Hi, I have a brand new nrf5340dk and the debug interface is not showing up when connected: I have other nrf5340s that work so I'm sure its the board specific.
Board label...
Hello,
Customer would like to know if part below:
NRF52840-DONGLE
Customer would like to know if there is any connector that Customer is able to use to the above part...
Hello,
I am relatively new to the nrf9161, but I am running into an error with my build.
'TFM_PERIPHERAL_DPPI_CHANNEL_MASK_SECURE' undeclared (first use in this function...
Hi there,
I intend to use pynrfjprog in development replacing another, older library. However, any call to the API which involves the nrfjprog DLL returns:
This is on...
Hi:
MCU: nRF52832
The device is powered by a battery. When the battery voltage drops to around 1.3V but is not completely depleted, if the device is charged at this time...
I am in the development phase of a Bluetooth based system design, which will be able to receive audio stream from any mobile device and play on the speaker, and also it would...
Hi,
I'd like to provision my Thingy91x for use with my nRF Cloud (so I can use location services). How do I provision the Thingy91x for use with my own nRF Cloud? What should...
Hi.
I read on the download site of the nrf command line tools that they are being deprecated.
I want to be sure that i'm correct here: 1. nrfjprog is replaced by nrfutil...
I have an application that runs on nrf9160 and uses nrf52811 for Bluetooth with client-host setup. Problem is it sometimes crashes on startup going into endless reboot loop...
Hi, I recently purchased an nRF52833DK and tested the attached code. When using Gazell, the maximum throughput I achieved was around 85,333 bps. However, according to the...
How to reproduce the issue:
We have used the standard hello_world sample application in the zephyr repository. CONFIG_I2C, CONFIG_SHELL and CONFIG_I2C_SHELL configurations...
Hi, I run this sample https://github.com/nrfconnect/sdk-nrf/tree/main/samples/bluetooth/mesh/dfu/distributor on two NRF52840DK, but I cpouldn't do the update, here is the...
I know that Zephyr supports its own test framework ZTest, but I have used CppUTest extensively on past projects.
I'm also using Quantum Leaps QP (for which there is a Zephyr...
Could I know how to enable openthread log in bulb project?
I have added some logs in modules/lib/openthread, but it can't be displayed in tool, how can I fix it？
BR
...
