we run long-term HIL tests with typically 3–8 nRF9151 DKs:
DKs spaced only about 1–3 cm apart
short USB 3.x cables to powered USB 3.2 hubs directly below them
sometimes...
Hi
Our project uses the nRF52833 SoC without an external PA. During the Korea KC spurious emission certification, the out-of-band emission on the first channel in DTM 2...
Hello,
I have been chasing this problem for some time, but it has been difficult to capture.
The issue occurs when the device is sitting idle (no eDRX or other power-saving...
Hi,
1.What is the maximum rate that the QSPI of nRF54L15 can achieve? 2. Is it possible for me to use QSPI to read the flash memory while simultaneously refreshing the screen...
Hi,
I want to ask if the Nrf54l05 supports application image compression. I asked Nordic AI and they said it’s not supported, but I want to know the reason why it’s not...
Can anyone verify what two pins are used for NFC on a FANSTEL - BM20C module? I've been in contact with Fanstel for over a week, but they haven't given me a definitive answer...
Hello all,
I am looking to hire a developer experienced with ANT+ together with BLE and the nRF52840 SoC, possibly the nrf54L10.
I am looking for the coding for the...
I wrote this function:
When calling it and
ptr points to something odd, the chip seems to crash. Can you not dereference odd memory addresses?
Or is there a different...
Hi,
I have been using nrf5340 audio dk fir the last couple weeks with nRF Connect SDK v2.1.0 and nRF Connect SDK v2.1.1. There were issues with the audio template for walkie...
Hi,
I'm using nRF Connect 2.1.1
I create a application based on 802154_phy_test template.
When I create a configuration and build for the nRF52840 it compiles OK.
...
Hello,
I have a TMP117 attached to I2C1 on a nrf5340 and am using the zephyr NCS v2.0.0 driver to communicate with it.
How can I configure I2C1 for power management...
Hi, I am looking to use mcuboot to manage 2 separate images. The idea is that under certain conditions, image 1 would jump to image 2.
To test the idea, I am using the zephyr...
When using the Toolchain Manager through the nRF Connect for Desktop app, the Toolchain Manager is failing to fetch the index files resulting in the version 2 toolchains being...
Hi there,
as already mentioned in other tickets I'm developing a usb to uart bridge based on the nrf52820. The nRF5 SDK version I'm using is 17.1.0.
Right now I'm facing...
Hi,
When nrf9160 as serial modem, can AT command be sent/received over SPI interface without modify FW ?
As I know, the UART interface is the default setting for transmission...
Hi,
I'm trying to connect multiple device on the same peripheral (nrf5340), but my peripheral does not restart advertising once a device is connected.
How to reproduce...
Now we don't add the external capacitance and want to change the internal capacitance . I have install the test tool and send the command to write the register,but it seems...
Hi!
I have nRF5340 Devkits and already have my own PCBs with nRF5340 chips onboard. I have a task where I need to evaluate how good will be BLE signal in different locations...
I know that I can memory-map external flash using XIP in the NRF52 and NRF53. However, with XIP, you can't write to the memory-mapped addresses (makes sense since you don...
Hi,
I have written a code for the motor driver and that is going to be flashed onto nRF5340. There are two communication buses that I am using in the code: UART and GPIO...
Hello Nordic,
we want to use the nrf9160 to measure some stuff and send data to a server while being battery powered. Therefore we need the lowest power consumption possible...
hi is there any existing frameworks for the nrf52 avoiding zephyr. (eg using common native cmsis / freertos / lwip stacks)?
ideally looking for free (non keil) based SD...
