Running a test that sends a small ping packet to a server about 1/minute and I'm seeing intermittent board resets. I'm still trying to track down the cause, but in one case...
Hello Nordic support,
We are designing a battery-powered device using the u-blox NORA-B206-00B module, based on the nRF54L15. u-blox support recommended contacting you regarding...
Hi Nordic DevZone,
We are currently looking at how best to handle nRF9151 programming in mass production, and I would like to understand Nordic’s intended approach a bit...
Hello, The nRF9151 hardware design guidelines (power sequence) require VDD_GPIO to be applied at least 6 ms after VDD and ENABLE, after the hardware boot. In our design a...
I'm not sure if I can share the files here, but you can email me at kc6ete at gmail if you want a copy It's a four color print designed for the Snapmaker U1 though it can...
Dear Team,
I have been running two nRF54LM20-DK as Initiator and Reflector for Bluetooth Channel Sounding.
I adjusted the ranging algorithm RAS_Initiator to print Local...
Hi,
I'm trying to find out how people automate current measurements with the PPK2 beyond doing it by hand in the Power Profiler app.
From the threads here it looks like...
Hi,
I recently started with nRF52840-DK, Zephyr and nRF Connect SDK (v. 1.9.1). I want to test extended advertising. Since there is no example of "pure" extended advertising...
Hi Nordic team,
I am working on a project with one central and several peripheral BLE devices. The peripherals are moving randomly, is it possible to detect the event...
Hi, recently testing nrf9160 SMS example, but seems not working in both Send/Receive
I confirm that SMS is valid in my SIM Card, I put it in my mobile phone and verified...
Can you please explain how the %XCOUNTRYDATA command can speed up network selection in a new location? Does the modem perform a general scan on all bands to determine the...
hello , I am working spi with softdevice(i.e., bluetooth). here spi master is nrf52 and spi slave is ad9837. the spi interface code works fine without soft device(i.e.,ble...
Hello, we are developing a keyboard with two types of connections, via USB and Bluetooth using the nRF52833 chip.
We have all the firmware developed in Arduino since it...
Hi,
I am trying to compile the cfb sample as provided in v2.0.0.
my overlay file is as follows
and my prj file
When I try to build, I get the following error...
is there a way to change the target device to nRF52820 (PCA10100) in segger embedded studio? initially configured to nRF52832 when we started our setup (nRF Connect Desktop...
I want to design a general module. Is it feasible to design the schematic diagram in this way?
1.VDDH is powered by external power supply, is that ok?
2.VBUS is powered...
Hi,
We want to check how changing system voltage affects on GPS reception, for that we need to know the RSSI of each satellite the model use.
I know I can get the C2N...
This is in reference to: devzone.nordicsemi.com/.../getting-started-with-nordics-secure-dfu-bootloader
On step B1, it says: " Next step, inside SDKFolder\external\micro...
Hi,
I'm working on a project where the NRF52840 chip is connected to multiple peripherals (4 of them) through SPI. The hardware has been designed in a way that each peripheral...
Hi, I am using the ant_plus/ant_bpwr/bpwr_rx code as a reference to capture power data from an SRM power meter. I am at the point where I get the following messages, which...
Title says most of it. I'm wanting to perform an OTA DFU of an nRF52840 running NCS 2.0.0 using my android from either the nRF Connect Device Manager or nRF DFU app. There...
This is my first time developing for Nordic processors. I am using Zephyr 3.0.99 with the nrf52810 on a ublox BMD-330 eval board. I connected a W25X20CL 2M-bit chip via the...