Hello Nordic Community,
We are developing a custom product based on nRF9151 using NCS SDK v3.1.0 .
On the hardware side, we have already completed antenna matching and...
Hello,
We are trying to assess signal quality while synced to a BIS and we would like to use the RSSI values. RSSI values do show up when scanning and at least in the...
Hi Nordic Team,
We are currently evaluating nRF54L15 for our product design and thermal verification process.
According to the public datasheet, we can find the operating...
I'm setting up a script we will use at production time to write some data to an external flash module connected via SPI to a nRF54H20.
I used the following as reference...
Hello.
I need some advice - I'm a beginner. I tested the transition to sleep mode via __WFI for the nrf52840 Dongle (VS code, SDK v3.3.0). I need some advice - I'm a beginner...
Hi all — I'm developing a custom nRF5340 development board (Raytac MDBT53-1M) and would value the community's honest read on whether it's worth producing.
The goal is...
Hello,
I'm having trouble saving signing keys to the KMU on the nRF54LM20-DK.
I'm using the build for the nRF54LM20B, as recommended here, so the KMU should be used for...
Hello
I want to measure Low power current in nrf52840-DK with System ON mode.
I need to know how much current consumes by nrf52840 SoC while I2C Engine ON, SPI ON, and...
Hi.
I am working with the nrfConnect SDK 1.8.0. I would like to configure the nrf5340 for maximum throughput to work as a server for a smartphone device.
How should...
Hi all,
I am using NRF52840 and I am saving some data to the flash memory using fds. The data are 216 bytes in each file and there are 3400 files which is in total 734kbytes...
Hi,
In my application, I am writing in flash.
But when I do so, my openthread data in flash gets o verwritten, the node doesn't retain its commissioning data.
In nrf_SDK_For_Thread_and_Zigbee...
Hi All ,
I am using nrf9160Dk ,When i use asset tracker V2 i successfully get the GPS values on the nrf Cloud . But when i use the Asset Tracker only then i am unable to...
Hi there,
From the product specification of the nrf5340, we can only find UARTE peripherals (UART with EasyDMA). Is it possible to implement uart without DMA? Of course...
Hi
I was just curious as to whether or not there is a specific reason the Xenon's PWM capabilities are not available with NCS/Zephyr. Is there a hard limitation or is this...
Hi Team,
SDK - 17.1.0
chip -nrf52810
I want to store sensor data (12 bytes) every 30 seconds in flash memory. Once the flash is full, I want to replace the old data...
I'm trying to interface with the ds1339 real time clock to set and read the time for timestamping tasks in ncs 1.8.0. I've found a few tutorials that boil down to:
1....
Hello !
I can see this error event is deprecated.
What other registers can be used if any error occurs during on-fly encryption/decryption process ?
In case of RX ,...
Hi,
I was implementing ZigBee coordinator in nrf connect v1.18.0 to connect sensor which develops from template sample. every thing went fine until I add install code (took...
Hi there!
I face issue with setting the connection using PHY Coded.
I've:
- set the #define NRF_BLE_SCAN_SCAN_PHY 4 (it's Coded one) on Central side.
- forced PHY...
Hi,
I am using nRF52832 EV board (PCA10040 1.2.4) to develop my application.
Also, I am using nRF Connect SDK (version 1.8.0) with VS Code.
After I create the example...
