Hi DevZone,
I am currently working on a project that uses MCUboot (DFU over BLE) on the CPUAPP core together with a custom FLPR application.
I successfully got this working...
I'm trying to download Firmware for Smart Remote 3 for nRF52 but the download link sends me to a blank page Series nordicsemi.com/api/sitecore/Products/MedialibraryZipDownload...
Hi Nordic,
We are building a custom board using the nRF9151 LACA.
We see a back-powering issue between the GNSS antenna bias rail and VDD_GPIO.
Setup:
VDD_GPIO...
nRF54L15 FOTA Failure:
MCUboot reports magic=bad on Slot 0 and magic=unset on Slot 1 using NSIB + MCUboot + TF-M with Pure DTS Partitioning
Description
I am implementing...
Hi,
I am experiencing an issue where SPI read operations fail after upgrading from NCS 3.2.4 to NCS 3.4.0.
Hardware:
Custom board based on nRF52840
ADS1294...
Hello,
We have a project currently using NCS v3.2.3. We delivered the first production series of 50 units already, with the NSIB from this NCS version. We use the NSIB with...
May I ask if the nRF54L15 comes with a default state when shipped, or is it blank? Also, what’s the GPIO status? I’m asking because it will connect with the AP, and I’m worried...
Hi,
We want to know more about DMA in I2C,
we are using TWI Master and Slave drivers as mentioned here in this blog https://devzone.nordicsemi.com/guides/nrf-connect...
I've been trying to build blinky using the nRF SDK from the toolchain manager with no success on windows 10. I've previously been able to build projects so I'm not entirely...
I would like to make my own project of an analog sensor with BLE feature. Is it a good idea to go with third party module (because of the easy availability of Antenna)? can...
Hi! I measure the micro frequency by Hantek Osiloskop in two-mode.
First, I use a simple Blink without softdevice , reaching 570kHz in 10us. Second, I use a ble_app_blinky...
Hi, I am looking for some help in interfacing STM32F4 MCU and nRF52832 module via UART for establishing BLE communication. My application needs both the devices.
I downloaded...
Hello everyone,
how can I implement a blacklist for my central which is scanning for a UUID and should also check for example device name. If the device name is in the blacklist...
We have developed a sensor application using ESB protocol with the nRF SDK (nRF52832 on Tx side and nRF52840 on Rx side).
We would like to redevelop now the receiver under...
Hi
1、I made the following modifications to the hello_world example（ncs1.7.0\v1.7.0\zephyr\samples\hello_world.
2、I have disabled uart0,But the average power...
Hi,
I'd want to implement RTC for regular testing of a variable. I am largely based on The BLE_uart exemple and have added a timer instance and a PWM instance. As the...
Hello,
I run a piece of code on NCS1.8.0 on nRF5340-DK, and it returns -35 when executing k_msgq_get()，b ut the same code runs on NCS1.5.0 and the k_msgq_get() function...
Hello.
I am developing using nrf52832 (S132 v7.0.1, SDK v17.0.0).
Since I want to bond with Android, I have created a central code that summarizes the functions that I...
Hello everyone i am trying to integrate nRF Calendar example with the nRF5 Thread MQTTSN example. In my application, I will get the date and time source from the MQTT-SN JSON...
Hello,
I have a zephyr project built using NCS v1.8.0 with target board selected as nRF9160DK_nrf9160_ns. I am interfacing LSM6DSO sensor with nRF9160 dk, with interrupt...
Hello,
We have a firmware developed for Full Thread Device. But now as i want to reduce power consumption i want to convert FTD device firmware to SED firmware.
SDK...
